Land Cruiser URJ200 URJ202 GRJ200 VDJ200 - PARK ASSIST / MONITORING
PARKING ASSIST MONITOR SYSTEM (w/ Side Monitor System) - DATA LIST / ACTIVE TEST
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Chassis / Parking Assist Monitor System / Data List.
Enter the following menus: Body / Main body / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| AVC-LAN Master Reset Status | AVC-LAN communication condition / OK or NG | OK: AVC-LAN communication condition is normal NG: AVC-LAN communication condition is abnormal | - |
| AVC-LAN Master Status | AVC-LAN communication condition / OK or NG | OK: AVC-LAN communication condition is normal NG: AVC-LAN communication condition is abnormal | - |
| AVC-LAN Connect Status | AVC-LAN communication condition / OK or NG | OK: AVC-LAN communication condition is normal NG: AVC-LAN communication condition is abnormal | - |
| AVC-LAN Sending Status | AVC-LAN communication condition / OK or NG | OK: AVC-LAN communication condition is normal NG: AVC-LAN communication condition is abnormal | - |
| AVC-LAN Regist Complete Status | AVC-LAN communication condition / OK or NG | OK: AVC-LAN communication condition is normal NG: AVC-LAN communication condition is abnormal | - |
| AVC-LAN Regist Request Status | AVC-LAN communication condition / OK or NG | OK: AVC-LAN communication condition is normal NG: AVC-LAN communication condition is abnormal | - |
| VGRS With or Without Status | Displays "Parking Assist ECU's internal data may or may not match the "with/without VGRS" data that has been input" / OK or NG. | OK: Data Verification Normal NG: Data Verification Abnormal | - |
| Destination Data Check | Verification of Destination Data / OK or NG | OK: Data Verification Normal NG: Data Verification Abnormal | - |
| EEPROM Status (Initial read) | Parking assist ECU information / OK or NG | OK: Parking assist ECU is normal NG: Parking assist ECU is abnormal | - |
| IG Voltage Low Status | IG voltage input to parking assist ECU / OK or NG | OK: IG voltage is normal NG: IG voltage is abnormal (too low) | - |
| IG Voltage High Status | IG voltage input to parking assist ECU / OK or NG | OK: IG voltage is normal NG: IG voltage is abnormal (too high) | - |
| ACC Voltage Low Status | ACC voltage input to parking assist ECU / OK or NG | OK: ACC voltage is normal NG: ACC voltage is abnormal (too low) | - |
| ACC Voltage High Status | ACC voltage input to parking assist ECU / OK or NG | OK: ACC voltage is normal NG: ACC voltage is abnormal (too high) | - |
| AISIC Output Status | Output condition of camera display signal / OK or NG | OK: Output condition of camera display signal is normal NG: Output condition of camera display signal is abnormal | If displayed "NG", There is a malfunctions in parking assist ECU. |
| VGRS Relative Angle Status | Displays "VGRS may be active or inactive" / OK or NG | OK: VGRS normal NG: VGRS abnormal | - |
| Wheel Speed Sensor (4wheel) | Effectivity of speed signal from speed signal sensor / OK or NG | OK: Speed signal is effective NG: Speed signal is not effective | - |
| Number of DTC | Number of stored trouble codes / min.: 0, max.: 255 | Number of DTCs will be displayed | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Back Door Courtesy SW | Back door courtesy light switch signal / ON or OFF | ON: Back door open OFF: Back door closed | - |