DESCRIPTION
WIRING DIAGRAM
INSPECTION PROCEDURE
CHECK VEHICLE TYPE
CHECK CONNECTION OF NAVIGATION ANTENNA ASSEMBLY
REPLACE NAVIGATION ANTENNA ASSEMBLY
CLEAR DTC
CHECK DTC
CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
CHECK ANTENNA CORD SUB-ASSEMBLY
REPLACE TELEPHONE ANTENNA ASSEMBLY
CLEAR DTC
CHECK DTC
CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY
CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
CHECK ANTENNA CORD SUB-ASSEMBLY
REPLACE TELEPHONE ANTENNA ASSEMBLY
CLEAR DTC
CHECK DTC
DTC B15C0 Short in GPS Antenna
DTC B15C1 Open in GPS Antenna
DESCRIPTION
These DTCs are stored when a malfunction occurs in the navigation antenna assembly (w/o Roof Antenna) or telephone antenna assembly (w/ Roof Antenna).
DTC Code | DTC Detection Condition | Trouble Area |
B15C0 |
Navigation antenna error | w/o Roof Antenna
Navigation antenna assembly
Multi-media module receiver assembly
w/ Roof Antenna, w/o DAB Function
Telephone antenna assembly
No. 3 antenna cord sub-assembly
No. 2 antenna cord sub-assembly
Antenna cord sub-assembly
Multi-media module receiver assembly
w/ Roof Antenna, w/ DAB Function
Telephone antenna assembly
Digital audio broadcasting antenna assembly
No. 2 antenna cord sub-assembly
Antenna cord sub-assembly
Multi-media module receiver assembly
|
B15C1 |
Error of the power source to the navigation antenna |
WIRING DIAGRAM
INSPECTION PROCEDURE
Select the vehicle setting.
ResultResult | Proceed to |
w/o Roof Antenna | A |
w/ Roof Antenna, w/o DAB Function | B |
w/ Roof Antenna, w/ DAB Function | C |
2.CHECK CONNECTION OF NAVIGATION ANTENNA ASSEMBLY |
Check if the navigation antenna assembly is securely connected to the multi-media module receiver assembly.
- OK:
- Navigation antenna assembly is securely connected.
| SECURELY CONNECT NAVIGATION ANTENNA ASSEMBLY |
|
|
3.REPLACE NAVIGATION ANTENNA ASSEMBLY |
Replace the navigation antenna assembly with a normally functioning one ().
Recheck for DTCs and check if the same DTCs are output again ().
| REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY ()
|
|
|
OK | |
| |
END (NAVIGATION ANTENNA ASSEMBLY IS DEFECTIVE) |
|
6.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY |
Disconnect the No. 3 antenna cord sub-assembly from telephone antenna assembly connector.
Disconnect the No. 3 antenna cord sub-assembly from No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection | Condition | Specified Condition |
A-2 - B-1 | Always | Below 1 Ω |
A-2a - B-1a | Always | Below 1 Ω |
A-2 - Body ground | Always | 10 kΩ or higher |
A-2a - Body ground | Always | 10 kΩ or higher |
Text in Illustration*a | Front view of wire harness connector (to Telephone Antenna Assembly) |
*b | Front view of wire harness connector (to No. 2 Antenna Cord Sub-assembly) |
| REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY ()
|
|
|
7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY |
Disconnect the No. 2 antenna cord sub-assembly from No. 3 antenna cord sub-assembly.
Disconnect the No. 2 antenna cord sub-assembly from antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection | Condition | Specified Condition |
C-1 - D-1 | Always | Below 1 Ω |
C-1a - D-1a | Always | Below 1 Ω |
C-1 - Body ground | Always | 10 kΩ or higher |
C-1a - Body ground | Always | 10 kΩ or higher |
Text in Illustration*a | Front view of wire harness connector (to No. 3 Antenna Cord Sub-assembly) |
*b | Front view of wire harness connector (to Antenna Cord Sub-assembly) |
| REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY ()
|
|
|
8.CHECK ANTENNA CORD SUB-ASSEMBLY |
Disconnect the antenna cord sub-assembly from No. 2 antenna cord sub-assembly.
Disconnect the antenna cord sub-assembly from multi-media module receiver assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection | Condition | Specified Condition |
E-1 - GA-1 (GPS) | Always | Below 1 Ω |
E-1a - GA-1a | Always | Below 1 Ω |
E-1 - Body ground | Always | 10 kΩ or higher |
E-1a - Body ground | Always | 10 kΩ or higher |
Text in Illustration*a | Front view of wire harness connector (to No. 2 Antenna Cord Sub-assembly) |
*b | Front view of wire harness connector (to Multi-media Module Receiver Assembly) |
| REPLACE ANTENNA CORD SUB-ASSEMBLY ()
|
|
|
9.REPLACE TELEPHONE ANTENNA ASSEMBLY |
Replace the telephone antenna assembly with a normally functioning one ().
Recheck for DTCs and check if the same DTCs are output again ().
| REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY ()
|
|
|
OK | |
| |
END (TELEPHONE ANTENNA ASSEMBLY IS DEFECTIVE) |
|
12.CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY |
Disconnect the digital audio broadcasting antenna assembly from telephone antenna assembly connector.
Disconnect the digital audio broadcasting antenna assembly from No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection | Condition | Specified Condition |
A-2 - B-1 | Always | Below 1 Ω |
A-2a - B-1a | Always | Below 1 Ω |
A-2 - Body ground | Always | 10 kΩ or higher |
A-2a - Body ground | Always | 10 kΩ or higher |
Text in Illustration*a | Front view of wire harness connector (to Telephone Antenna Assembly) |
*b | Front view of wire harness connector (to No. 2 Antenna Cord Sub-assembly) |
| REPLACE DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY ()
|
|
|
13.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY |
Disconnect the No. 2 antenna cord sub-assembly from digital audio broadcasting antenna assembly.
Disconnect the No. 2 antenna cord sub-assembly from antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection | Condition | Specified Condition |
C-1 - D-4 | Always | Below 1 Ω |
C-1a - D-4a | Always | Below 1 Ω |
C-1 - Body ground | Always | 10 kΩ or higher |
C-1a - Body ground | Always | 10 kΩ or higher |
Text in Illustration*a | Front view of wire harness connector (to Digital Audio Broadcasting Antenna Assembly) |
*b | Front view of wire harness connector (to Antenna Cord Sub-assembly) |
| REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY ()
|
|
|
14.CHECK ANTENNA CORD SUB-ASSEMBLY |
Disconnect the antenna cord sub-assembly from No. 2 antenna cord sub-assembly.
Disconnect the antenna cord sub-assembly from multi-media module receiver assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection | Condition | Specified Condition |
E-4 - GA-1 (GPS) | Always | Below 1 Ω |
E-4a - GA-1a | Always | Below 1 Ω |
E-4 - Body ground | Always | 10 kΩ or higher |
E-4a - Body ground | Always | 10 kΩ or higher |
Text in Illustration*a | Front view of wire harness connector (to No. 2 Antenna Cord Sub-assembly) |
*b | Front view of wire harness connector (to Multi-media Module Receiver Assembly) |
| REPLACE ANTENNA CORD SUB-ASSEMBLY ()
|
|
|
15.REPLACE TELEPHONE ANTENNA ASSEMBLY |
Replace the telephone antenna assembly with a normally functioning one ().
Recheck for DTCs and check if the same DTCs are output again ().
| REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY ()
|
|
|
OK | |
| |
CHECK CONNECTION OF NAVIGATION ANTENNA ASSEMBLY |
|