РАСПРЕДВАЛ - СНЯТИЕ

Освободите 13 фиксаторов и снимите верхнее уплотнение кронштейна радиатора.

Remove the clip, 5 bolts and front bumper cover lower.

Remove the 4 bolts.

Unhook the engine under cover from the vehicle body as shown in the illustration.

Ослабьте пробку сливного крана радиатора.

• УКАЗАНИЕ:

• Слейте охлаждающую жидкость в контейнер и утилизируйте ее в соответствии с местными требованиями.

Слейте охлаждающую жидкость, сняв крышку радиатора.

Ослабьте пробку сливного крана блока цилиндров.

Ослабьте пробку сливного крана блока цилиндров и слейте охлаждающую жидкость из двигателя.

• ПРИМЕЧАНИЕ:

• Если охлаждающая жидкость не сливается через пробку сливного крана радиатора, пробки сливных кранов блока цилиндров и расширительный бачок радиатора, возможны засорение радиатора и утечка охлаждающей жидкости через уплотнение насоса системы охлаждения.

Remove the 4 clips and fender apron seal.

Disconnect the sensor connector.

Detach the wire harness clamp.

Loosen the hose clamp and remove the resonator with air cleaner cap.

Detach the 4 hook clamps, and then remove the air cleaner cap and resonator with air cleaner cap.

Remove the 3 bolts and air cleaner case.

Remove the terminal cap.

Remove the nut and generator wire.

Disconnect the generator connector and cooler compressor connector.

Detach the 4 wire harness clamps.

for LHD:

Detach the 4 wire harness clamps.

Remove the bolt and wiring harness clamp bracket.

Detach the clamp and remove the No. 1 radiator hose.

Remove the 2 nuts and hose clamp.

Disconnect the reservoir hose from the upper side of the radiator tank.

Remove the 3 bolts and radiator reservoir.

Loosen the 4 nuts holding the fluid coupling fan.

Remove the vane pump V belt and the fan and generator V belt (See page ).

Remove the 2 bolts holding the fan shroud.

Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

• ПРИМЕЧАНИЕ:

• Be careful not to damage the radiator core.

Remove the fan pulley from the water pump.

Remove the 4 bolts, vane pump drive pulley and cooler compressor drive pulley.

Using SST, remove the pulley bolt.

• SST
• 09213-54015(91651-60855)
  09330-00021

Using SST, remove the pulley.

• SST
• 09950-50013(09951-05010,09952-05010,09953-05020,09954-05021)
  09950-60010(09951-00490)
  09950-40011(09957-04010)

Remove the 2 bolts and Idle pulley bracket.

Remove the 11 bolts, washers, timing belt cover, and 2 gaskets.

Remove the timing belt guide.

Using the crankshaft pulley bolt, align the groove of the crankshaft pulley with the timing pointer by turning the crankshaft clockwise.

Text in Illustration

*1	Timing Mark
	Turn

Check that the timing marks of the camshaft timing pulley and No. 2 timing belt cover are aligned.

If not, turn the crankshaft 1 revolution (360°).

Turn the crankshaft 90° counterclockwise, and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.

Text in Illustration

Turn

• ПРИМЕЧАНИЕ:

• If the timing belt is disengaged, having the crankshaft timing pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when removing the camshaft timing pulley, and camshaft causing damage. Therefore, always set the crankshaft pulley is removed at the correct angle.

Loosen the No. 1 timing belt idler bolt (A), and shift the idler to the left as far as possible.

Text in Illustration

	Pry
	Move

Tighten the No. 1 timing belt idler bolt (A), and then relieve the timing belt tension.

Remove the timing belt.

Loosen the hose clamp and remove the 2 bolts and intake pipe.

Remove the 9 bolts, nut, cylinder head cover and gasket.

Using the crankshaft pulley bolt, turn the crankshaft 90° counterclockwise and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.

Text in Illustration

	Turn
*1	Timing Mark
*2	Protrusion

• УКАЗАНИЕ:

• Set the No. 1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.

Using SST, loosen the pulley bolt.

• SST
• 09960-10010(09962-01000,09963-01000)

Using SST, separate the timing pulley from the camshaft.

• SST
• 09950-50013(09951-05010,09952-05010,09953-05010,09954-05021)

Remove the pulley bolt and timing pulley.

Remove the timing pulley woodruff key.

Remove the 4 bolts and timing belt cover.

Remove the 4 bolts, retainer and gasket.

Using a screwdriver and hammer, tap out the oil seal.

Turn the camshaft with a wrench so that the key groove faces upward.

Uniformly loosen and remove the 10 bearing cap bolts in several steps in the sequence shown in the illustration.

Remove the 5 bearing caps and camshaft.

• УКАЗАНИЕ:

• Arrange the bearing caps in the correct order.