МАСЛЯНЫЙ НАСОС - УСТАНОВКА

Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing belt case edge.

• SST
• 09214-60010

Apply MP grease to the lip of the oil seal.

Place a new gasket on the cylinder block.

Install the timing belt case with the 5 bolts.

• Момент затяжки:
• 23 N*m{ 230 kgf*cm, 17 ft.*lbf}

Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.

• Момент затяжки:
• for nut:
• 21 N*m{ 210 kgf*cm, 17 ft.*lbf}
• for bolt:
• 18 N*m{ 184 kgf*cm, 13 ft.*lbf}

Remove any old packing (FIPG) material and do not drop any oil on the contact surfaces of the oil pan and cylinder block.

Apply seal packing to the oil pan as shown in the illustration.

• Seal packing:
• Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

• Application Specification:

• Item	Seal Packing Diameter	Seal Packing Application Length
  Dashed line	7.0 mm (0.276 in.)	128 mm (5.04 in.)
  Continuous line	5.0 mm (0.197 in.)	-

• УКАЗАНИЕ:

Install the oil pan with the 16 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several steps.

• Момент затяжки:
• 18 N*m{ 184 kgf*cm, 13 ft.*lbf}

Align the key groove of the timing pulley with the pulley set key.

Using SST and a hammer, tap in the timing pulley with the flange side facing inward.

• SST
• 09223-46011

Install the spacer and No. 2 timing belt idler with the bolt.

• Момент затяжки:
• 33 N*m{ 337 kgf*cm, 24 ft.*lbf}

Check that the No. 2 timing belt idler moves smoothly.

Install the No. 1 belt idler with the 3 bolts.

• Момент затяжки:
• for bolt A:
• 44 N*m{ 449 kgf*cm, 32 ft.*lbf}
• for bolt B, C:
• 19 N*m{ 195 kgf*cm, 14 ft.*lbf}

• УКАЗАНИЕ:

The bolt lengths for bolt A, B and C as follows.

Bolt C is combined with the No. 1 timing belt idler.

• Standard Bolt:

• Item	Length
  A	76.5 mm (3.01 in.)
  B	42.9 mm (1.69 in.)
  C	41.3 mm (1.63 in.)

Install a new gasket, the water pump and tension spring bracket with the 6 bolts.

• Момент затяжки:
• 23 N*m{ 236 kgf*cm, 17 ft.*lbf}

Install the timing belt cover with the 4 bolts.

• Момент затяжки:
• 18 N*m{ 184 kgf*cm, 13 ft.*lbf}

Install the woodruff key to the key groove of the camshaft.

Align the timing mark on the camshaft timing pulley with the timing mark on the No. 2 timing belt cover and temporarily install the pulley with the bolt.

Using SST, tighten the bolt.

• SST
• 09960-10010(09962-01000,09963-01000)

• Момент затяжки:
• 98 N*m{ 999 kgf*cm, 72 ft.*lbf}

Install the generator bracket with the 3 bolts.

• Момент затяжки:
• 49 N*m{ 500 kgf*cm, 36 ft.*lbf}

Install the engine mounting bracket with the 4 bolts.

• Момент затяжки:
• 49 N*m{ 500 kgf*cm, 36 ft.*lbf}

Install the engine mounting bracket with the 4 bolts.

• Момент затяжки:
• 49 N*m{ 500 kgf*cm, 36 ft.*lbf}

Install the pump bracket with the 3 bolts.

• Момент затяжки:
• for bolt A:
• 57 N*m{ 581 kgf*cm, 42 ft.*lbf}
• except bolt A:
• 78 N*m{ 795 kgf*cm, 58 ft.*lbf}

Clean the threads of the water by-pass hose union and apply adhesive to them.

• Adhesive:
• Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

Install the water by-pass hose union.

• Момент затяжки:
• 39 N*m{ 398 kgf*cm, 29 ft.*lbf}

Install a new gasket to the cylinder head.

Install the outlet hosing with the 3 bolts

• Момент затяжки:
• 19 N*m{ 194 kgf*cm, 14 ft.*lbf}

Install the injection pump (See page ).

Install the timing belt (See page ).

Install the No. 1 compressor mounting bracket with the 4 bolts.

• Момент затяжки:
• 81 N*m{ 829 kgf*cm, 60 ft.*lbf}

Install the engine (See page ).