DTC P0088 Fuel Rail / System Pressure - Too High
DTC P1229 Fuel Pump System
Description
Monitor description
Monitor strategy
Typical enabling conditions
Typical malfunction thresholds
Inspection procedure
Description DTC P0088 P1229
Toyota fault code list DTC P0088 P1229
DTC No. | DTC Detection Condition | Trouble Area |
P0088 | Internal fuel pressure of common rail is too high: Fuel pressure exceeds 200 MPa (2,039 kgf/cm2, 29,007 psi) (1 trip detection logic) |
|
P1229 | Fuel over-feed: Internal fuel pressure continues exceeding target fuel pressure despite ECM closing suction control valve (1 trip detection logic) |
|
HINT:
- DTC P0088 and P1229 can be detected if the vehicle is driven at 50 km/h (31 mph) for 5 minutes.
- For more information on the supply pump (suction control valve) and common rail system, refer to the system description.
- When DTC P0088 and/or P1229 is set, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Press.
Engine Speed | Fuel Pressure |
Idling | Approximately 37 to 43 MPa |
3,000 rpm (No engine load) | Approximately 60 to 66 MPa |
Monitor description DTC P0088 DTC P1229
- P0088 (Internal fuel pressure too high):
The ECM sets this DTC if the fuel pressure inside the common rail is more than 200 MPa (2,039 kgf/cm2, 29,007 psi). This DTC indicates that: 1) the suction control valve may be stuck open or 2) there may be a short in the suction control valve circuit.
If this DTC is set, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.
- P1229 (Fuel over-feed):
The ECM sets this DTC if the actual fuel pressure inside the common rail remains higher than the target fuel pressure, despite the ECM closing the suction control valve. This DTC indicates that the suction control valve may be stuck open, or there may be a short in its circuit. Under this condition, the pressure discharge valve operates frequently.
If this DTC is set, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.
Monitor strategy DTC P0088 DTC P1229
Required sensor | Fuel pressure sensor |
Frequency of operation | Continuous |
Duration | 1 second |
MIL operation | 1 driving cycle |
Required sensor | Fuel pressure sensor |
Frequency of operation | Continuous |
Duration | 10 minutes |
MIL operation | 1 driving cycle |
Typical enabling conditions DTC P0088 DTC P1229
Specification |
The monitor will not run if the fuel pressure sensor or suction control valve circuit is malfunctioning. |
Item | Specification |
Target fuel pressure variation | Small |
The monitor will not run if the fuel pressure sensor or suction control valve circuit is malfunctioning. |
Typical malfunction thresholds DTC P0088 DTC P1229
Detection Criteria | Threshold |
Fuel pressure sensor | 200 MPa (2,039 kgf/cm2, 29,007 psi) or more |
Detection Criteria | Threshold |
The internal fuel pressure of the common rail when the suction control valve is closed. | Remains higher than target fuel pressure |
Wiring diagram
Inspection procedure
NOTICE:
- After replacing the ECM, the new ECM needs registration and initialization.
- After replacing a supply pump, the ECM needs initialization.
1.Check other dtc output (in addition to dtc p0088 and/or p1229)
-
Connect the intelligent tester to the DLC3.
-
Turn the ignition switch on (IG) and turn the tester ON.
-
Enter the following menus: Powertrain / Engine and ECT / DTC.
-
Read the DTCs.
Result:
Display (DTC Output) Proceed to P0088 and/or P1229 A P0190, P0192 and/or P0193 B
|
|
A | |
2.Inspect supply pump assembly (suction control valve)
-
Disconnect the B46 suction control valve connector.
-
Measure the resistance of the suction control valve.
Standard resistance:
Tester Connection Condition Specified Condition B46-1 - B46-2 20°C (68°F) 1.9 to 2.3 ?
-
Reconnect the suction control valve connector.
|
|
||||
OK | |
3.Check if dtc output recurs
-
Connect the intelligent tester to the DLC3.
-
Turn the ignition switch on (IG) and turn the tester ON.
-
Clear DTCs.
-
Disconnect the suction control valve connector and then start the engine. Wait for 1 minute.
-
Enter the following menus: Powertrain / Engine and ECT / DTC.
-
Read the DTCs.
Result:
Display (DTC Output) Proceed to No output or engine does not start A P1229 B
-
Reconnect the suction control valve connector.
|
|
||||
A | |
4.Check wire harness (scv - ecm)
-
Disconnect the B46 valve connector.
-
Disconnect the B32 ECM connector.
-
Measure the resistance of the wire harness side connectors.
Standard resistance:
Tester Connection Specified Condition B46-1 - B32-42 (PCV+) Below 1 ? B46-2 - B32-41 (PCV-) Below 1 ? B46-1 or B32-42 (PCV+) - Body ground 10 k? or higher B46-2 or B32-41 (PCV-) - Body ground 10 k? or higher
-
Reconnect the suction control valve connector.
-
Reconnect the ECM connector.
|
|
||||
OK | |
5.Replace common rail assembly
-
Replace the common rail assembly.
NEXT | |
6.Check whether dtc output recurs
-
Connect the intelligent tester to the DLC3.
-
Turn the ignition switch on (IG) and turn the tester ON.
-
Clear DTCs.
-
Start the engine and drive the vehicle for approximately 15 minutes.
-
Enter the following menus: Powertrain / Engine and ECT / DTC.
-
Read the DTCs.
Result:
Display (DTC Output) Proceed to P0088 and/or P1229 A No output B
|
|
||||
A | |
REPLACE ECM