Toyota
Camry ACV40 GSV40
Repair Manual
2Gr-Fe Engine Control System
Sfi System
SFI SYSTEM > Fuel Injector Circuit
DESCRIPTION
The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.WIRING DIAGRAM

INSPECTION PROCEDURE

Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Turn the engine switch on (IG).
Measure the voltage between the terminals.
- Standard voltage:
- RHD:
Tester Connection Specified Condition #10 (C58-45) - E01 (C58-22) 11 to 14 V #20 (C58-85) - E01 (C58-22) 11 to 14 V #30 (C58-44) - E01 (C58-22) 11 to 14 V #40 (C58-84) - E01 (C58-22) 11 to 14 V #50 (C58-43) - E01 (C58-22) 11 to 14 V #60 (C58-83) - E01 (C58-22) 11 to 14 V - LHD:
Tester Connection Specified Condition #10 (C55-45) - E01 (C55-22) 11 to 14 V #20 (C55-85) - E01 (C55-22) 11 to 14 V #30 (C55-44) - E01 (C55-22) 11 to 14 V #40 (C55-84) - E01 (C55-22) 11 to 14 V #50 (C55-43) - E01 (C55-22) 11 to 14 V #60 (C55-83) - E01 (C55-22) 11 to 14 V
Reconnect the ECM connector.
| CHECK FOR INTERMITTENT PROBLEMS | |||
| NG | |
![]() |
Inspect the injector assembly (Click here).
| REPLACE INJECTOR ASSEMBLY (Click here) | |||
| OK | |
![]() |

Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
- Standard resistance:
Tester Connection Specified Condition 3 - 5 10 kΩ or higher 3 - 5 Below 1 Ω
(Apply battery voltage between terminals 1 and 2)
Reinstall the IG2 relay.
| REPLACE IGNITION RELAY NO. 2 | |||
| OK | |
![]() |

Disconnect the injector connector.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
- Standard resistance:
- RHD:
Tester Connection Specified Condition #10 (C58-45) - C7-1 Below 1 Ω #20 (C58-85) - C9-1 Below 1 Ω #30 (C58-44) - C8-1 Below 1 Ω #40 (C58-84) - C10-1 Below 1 Ω #50 (C58-43) - C36-1 Below 1 Ω #60 (C58-83) - C37-1 Below 1 Ω #10 (C58-45) or C7-1 - Body ground 10 kΩ or higher #20 (C58-85) or C9-1 - Body ground 10 kΩ or higher #30 (C58-44) or C8-1 - Body ground 10 kΩ or higher #40 (C58-84) or C10-1 - Body ground 10 kΩ or higher #50 (C58-43) or C36-1 - Body ground 10 kΩ or higher #60 (C58-83) or C37-1 - Body ground 10 kΩ or higher - LHD:
Tester Connection Specified Condition #10 (C55-45) - C7-1 Below 1 Ω #20 (C55-85) - C9-1 Below 1 Ω #30 (C55-44) - C8-1 Below 1 Ω #40 (C55-84) - C10-1 Below 1 Ω #50 (C55-43) - C36-1 Below 1 Ω #60 (C55-83) - C37-1 Below 1 Ω #10 (C55-45) or C7-1 - Body ground 10 kΩ or higher #20 (C55-85) or C9-1 - Body ground 10 kΩ or higher #30 (C55-44) or C8-1 - Body ground 10 kΩ or higher #40 (C55-84) or C10-1 - Body ground 10 kΩ or higher #50 (C55-43) or C36-1 - Body ground 10 kΩ or higher #60 (C55-83) or C37-1 - Body ground 10 kΩ or higher
Reconnect the injector connector.
Reconnect the ECM connector.
| REPAIR OR REPLACE HARNESS OR CONNECTOR | |||
| OK | |
![]() |

Remove the IG2 relay from the engine room relay block.
Disconnect the injector connectors.
Measure the resistance between the terminals.
- Standard resistance (check for open):
Tester Connection Specified Condition C7-2 - IG2 relay terminal 3 Below 1 Ω C9-2 - IG2 relay terminal 3 Below 1 Ω C8-2 - IG2 relay terminal 3 Below 1 Ω C10-2 - IG2 relay terminal 3 Below 1 Ω C36-2 - IG2 relay terminal 3 Below 1 Ω C37-2 - IG2 relay terminal 3 Below 1 Ω
- Standard resistance (check for short):
Tester Connection Specified Condition C7-2 or IG2 relay terminal 3 - Body ground 10 kΩ or higher C9-2 or IG2 relay terminal 3 - Body ground 10 kΩ or higher C8-2 or IG2 relay terminal 3 - Body ground 10 kΩ or higher C10-2 or IG2 relay terminal 3 - Body ground 10 kΩ or higher C36-2 or IG2 relay terminal 3 - Body ground 10 kΩ or higher C37-2 or IG2 relay terminal 3 - Body ground 10 kΩ or higher
Reinstall the IG2 relay.
Reconnect the injector connectors.
| REPAIR OR REPLACE HARNESS OR CONNECTOR | |||
| OK | |
![]() |

Remove the IG2 fuse from the engine room relay block.
Measure the IG2 fuse resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the IG2 fuse.
| REPLACE IG2 FUSE | |||
| OK | |
![]() |

Remove the IG2 relay from the engine room relay block.
Measure the IG2 relay voltage.
- Standard voltage:
- 9 to 14 V
Reinstall the IG2 relay.
| REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - BATTERY) | |||
| OK | |
![]() |

Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
- Standard resistance:
Tester Connection Specified Condition IG2 relay terminal 2 - Body ground Below 1 Ω
Reinstall the IG2 relay.
- Result:
Result Proceed to OK A NG B
| REPAIR OR REPLACE HARNESS OR CONNECTOR | |||
| A | |
![]() |

Remove the IG2 relay from the engine room relay block.
Disconnect the E6 main body ECU connector.
Measure the resistance between the terminals.
- Standard resistance (check for open):
Tester Connection Specified Condition IG2 relay terminal 1 - IG2D (E6-11) Below 1 Ω
- Standard resistance (check for short):
Tester Connection Specified Condition IG2 relay terminal 1 or IG2D (E6-11) - Body ground 10 kΩ or higher
Reinstall the IG2 relay.
Reconnect the main body ECU connector.
| REPAIR OR REPLACE HARNESS OR CONNECTOR | |||
| OK | |
![]() | |
| GO TO ENTRY AND START SYSTEM | |


