Throttle Body - Removal(2006/01 - 2007/12)

Brand:

Toyota

Model Name:

Camry ACV40 GSV40

Manual:

Repair Manual

Section:

2Gr-Fe Engine Control System

Title:

Throttle Body

  1. Remove engine under cover lh

  2. Remove engine under cover rh

  3. Drain engine coolant

  4. Remove cool air intake duct seal

  5. Remove v-bank cover sub-assembly

  6. Remove air cleaner inlet assembly

  7. Remove air cleaner cap sub-assembly

  8. Remove air cleaner case sub-assembly

  9. Remove no. 1 air cleaner inlet

  10. Remove throttle body



​

1. REMOVE ENGINE UNDER COVER LH


2. REMOVE ENGINE UNDER COVER RH


3. DRAIN ENGINE COOLANT
NOTICE:
Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
  1. Remove the radiator cap sub-assembly from the radiator assembly.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs, then drain the coolant.


    Throttle Body - On-Vehicle Inspection Camry

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


4. REMOVE COOL AIR INTAKE DUCT SEAL
  1. Remove the 7 clips and intake duct seal. Camry
  2. Remove the 7 clips and intake duct seal.



5. REMOVE V-BANK COVER SUB-ASSEMBLY
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.NOTICE: Attempting to disengage both front and rear clips at the same time may cause the cover to break. Camry
  2. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.


6. REMOVE AIR CLEANER INLET ASSEMBLY
  1. Remove the 2 bolts, clamp and air cleaner inlet. Camry
  2. Remove the 2 bolts, clamp and air cleaner inlet.



7. REMOVE AIR CLEANER CAP SUB-ASSEMBLY
  1. Disconnect the 3 vacuum hoses. Camry
  2. Disconnect the 3 vacuum hoses.

  1. Disconnect the mass air flow meter connector (*1). Camry
  2. Disconnect the mass air flow meter connector (*1).

  1. Disconnect the No. 2 ventilation hose (*2).

  1. Disconnect the hose band (*3).

  1. Disconnect the 3 bands, and remove the air cleaner cap sub-assembly. Camry
  2. Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.



8. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
  1. Disconnect the vacuum hose and hose clamp. Camry
  2. Disconnect the vacuum hose and hose clamp.

  1. Remove the 3 bolts and air cleaner case.



9. REMOVE NO. 1 AIR CLEANER INLET
  1. Remove the bolt and No. 1 air cleaner inlet. Camry
  2. Remove the bolt and No. 1 air cleaner inlet.



10. REMOVE THROTTLE BODY
  1. Disconnect the throttle body connector and clamp. Camry
  2. Disconnect the throttle body connector and clamp.

  1. Disconnect the 2 water by-pass hoses from the throttle body. Camry
  2. Disconnect the 2 water by-pass hoses from the throttle body.

  1. Remove the 4 bolts and throttle body. Camry
  2. Remove the 4 bolts and throttle body.

  1. Remove the throttle body gasket from the intake air surge tank.