Sfi System - Vc Output Circuit(2009/01 - 2010/08)

Brand:

Toyota

Model Name:

Camry ACV40 GSV40

Manual:

Repair Manual

Section:

2Gr-Fe Engine Control System

Title:

Sfi System

  1. Description

  2. Wiring diagram

  3. Inspection procedure

  4. Check mil

  5. Check connection between intelligent tester and ecm

  6. Check throttle body assembly (check mil illuminated)

  7. Check accelerator pedal assembly (check mil illuminated)

  8. Check vvt sensor for intake camshaft bank 1 (check mil illuminated)

  9. Check vvt sensor for exhaust camshaft bank 1 (check mil illuminated)

  10. Check vvt sensor for intake camshaft bank 2 (check mil illuminated)

  11. Check vvt sensor for exhaust camshaft bank 2 (check mil illuminated)

  12. Check harness and connector

SFI SYSTEM > VC Output Circuit


​

DESCRIPTION

The ECM constantly uses 5 V from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that receive power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to the ON position. The MIL goes off when the engine is started.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to the ON position.OK:MIL lights up. Camry


WIRING DIAGRAM


Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to the ON position.OK:MIL lights up. Camry


Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to the ON position.OK:MIL lights up. Camry


INSPECTION PROCEDURE

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to the ON position.

    OK:
    MIL lights up.


OKnext
GO TO MIL CIRCUIT (Click here)
NG
next down

2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Check the communication between the tester and ECM.

    Result:

    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B


Anext
GO TO MIL CIRCUIT (Click here)
B
next down

3.CHECK THROTTLE BODY ASSEMBLY (CHECK MIL ILLUMINATED)
  1. Disconnect the throttle body connector.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B
  1. Reconnect the throttle body connector.



Anext
REPLACE THROTTLE BODY ASSEMBLY (Click here)
B
next down

4.CHECK ACCELERATOR PEDAL ASSEMBLY (CHECK MIL ILLUMINATED)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B
  1. Reconnect the accelerator pedal position sensor connector.



Anext
REPLACE ACCELERATOR PEDAL ASSEMBLY (Click here)
B
next down

5.CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED)
  1. Disconnect the connector from the VVT sensor for intake camshaft bank 1.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B
  1. Reconnect the connector to the VVT sensor for intake camshaft bank 1.



Anext
REPLACE VVT SENSOR FOR INTAKE CAMSHAFT BANK 1 (Click here)
B
next down

6.CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED)
  1. Disconnect the connector from the VVT sensor for exhaust camshaft bank 1.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B
  1. Reconnect the connector to the VVT sensor for exhaust camshaft bank 1.



Anext
REPLACE VVT SENSOR FOR EXHAUST CAMSHAFT BANK 1 (Click here)
B
next down

7.CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED)
  1. Disconnect the connector from the VVT sensor for intake camshaft bank 2.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B
  1. Reconnect the connector to the VVT sensor for intake camshaft bank 2.



Anext
REPLACE VVT SENSOR FOR INTAKE CAMSHAFT BANK 2 (Click here)
B
next down

8.CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED)
  1. Disconnect the connector from the VVT sensor for exhaust camshaft bank 2.

  1. Turn the ignition switch to the ON position.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B
  1. Reconnect the connector to the VVT sensor for exhaust camshaft bank 2.



Anext
REPLACE VVT SENSOR FOR EXHAUST CAMSHAFT BANK 2 (Click here)
B
next down

9.CHECK HARNESS AND CONNECTOR
  1. Disconnect the throttle body connector. Camry
  2. Disconnect the throttle body connector.

  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the the connector from VVT sensor for intake camshaft bank 1.

  1. Disconnect the connector from the VVT sensor for exhaust camshaft bank 1.

  1. Disconnect the connector from the VVT sensor for intake camshaft bank 2.

  1. Disconnect the connector from the VVT sensor for exhaust camshaft bank 2.

  1. Disconnect the C58 (RHD) and A24 (RHD), or C55 (LHD) and A55 (LHD) ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    RHD:
    Tester Connection
    Specified Condition
    VCTA (C58-96) - Body ground
    10 kΩ or higher
    VCV1 (C58-115) - Body ground
    10 kΩ or higher
    VCV2 (C58-113) - Body ground
    10 kΩ or higher
    VCE1 (C58-114) - Body ground
    10 kΩ or higher
    VCE2 (C58-112) - Body ground
    10 kΩ or higher
    VCPA (A24-57) - Body ground
    10 kΩ or higher
    VCP2 (A24-58) - Body ground
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    VCTA (C55-96) - Body ground
    10 kΩ or higher
    VCV1 (C55-115) - Body ground
    10 kΩ or higher
    VCV2 (C55-113) - Body ground
    10 kΩ or higher
    VCE1 (C55-114) - Body ground
    10 kΩ or higher
    VCE2 (C55-112) - Body ground
    10 kΩ or higher
    VCPA (A55-57) - Body ground
    10 kΩ or higher
    VCP2 (A55-58) - Body ground
    10 kΩ or higher
  1. Reconnect the ECM connectors.

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the connector to the VVT sensor for exhaust camshaft bank 2.

  1. Reconnect the connector to the VVT sensor for intake camshaft bank 2.

  1. Reconnect the connector to the VVT sensor for exhaust camshaft bank 1.

  1. Reconnect the connector to the VVT sensor for intake camshaft bank 1.

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the throttle body connector.



NGnext
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
next down
REPLACE ECM (Click here)