Toyota
Camry ACV40 GSV40
Repair Manual
2Gr-Fe Engine Control System
Sfi System
SFI SYSTEM > Cranking Holding Function Circuit
DESCRIPTION
The cranking holding control system provides current to the starter when the ECM detects the engine switch start signal (STSW). When the ECM judges that the engine has started , the system cuts current to the starter. When the ECM receives the STSW signal, the ACC (Accessory) relay is turned off to prevent flickering of the combination meter, clock and audio system. Also, the STAR output signal travels through the ST cut relay and the park/neutral position switch assembly to the ST relay, causing the starter to activate.When the engine is cranking, the starter operation signal is received by the STA terminal of the ECM.

WIRING DIAGRAM
Refer to DTC P0617 (Click here).INSPECTION PROCEDURE
When starting the engine, check whether the starter motor starts.
| CHECK FOR INTERMITTENT PROBLEMS | |||
| NG | |
![]() |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Select the following menu items: Powertrain / Engine / Data List / Starter Signal. Read the values.
Check the result when the engine switch is turned on (IG) and when the engine is started.
- Standard:
Display (Starter Signal) Condition OFF Engine switch on (IG) ON Engine start
| Go to step 7 | |||
| NG | |
![]() |

Disconnect the A24 (RHD) or A55 (LHD) ECM Connector.
Measure the voltage between the terminal of the ECM connector and body ground while cranking the engine.
- Standard voltage:
- RHD:
Tester Connection Specified Condition STSW (A24-14) - Body ground 11 to 14 V - LHD:
Tester Connection Specified Condition STSW (A55-14) - Body ground 11 to 14 V
Reconnect the ECM connector.
| Go to step 11 | |||
| OK | |
![]() |

Remove the ST CUT relay from the engine room R/B.
Measure the voltage between the terminals of the engine room R/B and body ground while cranking the engine.
- Standard voltage:
Tester Connection Specified Condition ST CUT relay (3) - Body ground 11 to 14 V
Reinstall the ST CUT relay.
| Go to step 8 | |||
| OK | |
![]() |

Remove the ST CUT relay from the engine room R/B.
Measure the resistance between the terminals.
- Standard resistance:
Tester Connection Specified Condition 3 - 5 10 kΩ or higher 3 - 5 Below 1 Ω
(when battery voltage applied between terminals 1 and 2)
Reinstall the ST CUT relay.
| REPLACE ST CUT RELAY | |||
| OK | |
![]() |

Inspect the Park/Neutral Position (PNP) switch.
Disconnect the C1 switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Gear Selector Lever Position Tester Connection Specified Condition P 4 - 5 Below 1 Ω N 4 - 5 Below 1 Ω
Reconnect the PNP switch connector.
| REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here) | |||
| OK | |
![]() | |
| CHECK HARNESS AND CONNECTOR | |

Remove the ST relay from the engine room R/B.
Measure the resistance between the terminals.
- Standard resistance:
Tester Connection Specified Condition 3 - 5 10 kΩ or higher 3 - 5 Below 1 Ω
(when battery voltage applied between terminals 1 and 2)
Reinstall the ST relay.
| REPLACE STARTER RELAY | |||
| OK | |
![]() |

Disconnect the C1 park/neutral position switch connector.
Remove the ST relay from the engine room R/B.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
Tester Connection Specified Condition C1-9 - ST relay terminal (1) Below 1 Ω
- Standard resistance (Check for open):
Tester Connection Specified Condition C1-9 or ST relay terminal (1) - Body ground 10 kΩ or higher
Reinstall the ST relay.
| REPAIR OR REPLACE HARNESS OR CONNECTOR | |||
| OK | |
![]() |

Remove the ST relay from the engine room R/B.
Measure the voltage between the terminals of the engine room R/B and body ground.
- Standard voltage:
Tester Connection Specified Condition ST relay (5) - Body ground 11 to 14 V
| REPAIR OR REPLACE HARNESS OR CONNECTOR | |||
| OK | |
![]() |
Inspect the starter assembly (Click here).
| REPAIR OR REPLACE STARTER ASSEMBLY | |||
| OK | |
![]() | |
| REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY - STARTER, STARTER - BATTERY) | |

Disconnect the E9 main body ECU connector.
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
- RHD:
Tester Connection Specified Condition STSW (E9-4) - STSW (A24-14) Below 1 Ω - LHD:
Tester Connection Specified Condition STSW (E9-4) - STSW (A55-14) Below 1 Ω
- Standard resistance (Check for short):
- RHD:
Tester Connection Specified Condition STSW (E9-4) or STSW (A24-14) - Body ground 10 kΩ or higher - LHD:
Tester Connection Specified Condition STSW (E9-4) or STSW (A55-14) - Body ground 10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the ECM connector.
| REPAIR OR REPLACE HARNESS OR CONNECTOR | |||
| OK | |
![]() | |
| GO TO ENTRY AND START SYSTEM (Click here) | |



