Rear Door Lock (For Sedan) Removal
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)
REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)
REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)
REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
REMOVE REAR DOOR TRIM BRACKET
REMOVE REAR DOOR SERVICE HOLE COVER
REMOVE REAR DOOR CHECK ASSEMBLY
REMOVE REAR DOOR WEATHERSTRIP
REMOVE REAR DOOR BELT MOULDING
REMOVE REAR DOOR GLASS RUN
REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
REMOVE REAR DOOR GLASS SUB-ASSEMBLY
REMOVE REAR DOOR LOCK
Rear Door Lock (For Sedan) -- Removal |
- HINT:
- Use the same procedure for both the RH and LH sides.
- The procedure described below is for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
2. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window) |
Insert a clip remover between the plate and door trim.
Turn the handle with the clip remover inserted, as shown in the illustration.
Remove the rear door window regulator handle assembly and clip.
Remove the window regulator handle plate.
3. REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window) |
Remove the screw.
Disengage the 4 claws and remove the rear door armrest base upper panel.
4. REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window) |
Remove the screw.
Disengage the 7 claws and 2 clips and remove the rear door armrest base upper panel.
Disconnect the connector.
5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
Remove the screw.
Disengage the 7 clips.
Disconnect the rear door lock remote control cable and rear door inside locking cable and remove the rear door trim board.
6. REMOVE REAR DOOR TRIM BRACKET |
Remove the 2 screws and the rear door trim bracket.
7. REMOVE REAR DOOR SERVICE HOLE COVER |
Disconnect the connectors and clamps, then remove the rear door service hole cover.
- NOTICE:
- Remove any tape remaining on the door side.
8. REMOVE REAR DOOR CHECK ASSEMBLY |
Remove the 3 bolts, then remove the rear door check.
- NOTICE:
- Do not drop or damage the door check when removing the bolts.
- HINT:
- Remove the door check through the service hole.
9. REMOVE REAR DOOR WEATHERSTRIP |
Disengage the 32 clips and remove the rear door weatherstrip.
- NOTICE:
- Remove any tape remaining on the door side.
10. REMOVE REAR DOOR BELT MOULDING |
Apply protective tape to the door panel in the periphery of the rear door belt moulding.
Using a moulding remover, disengage the 5 claws and remove the rear door belt moulding.
11. REMOVE REAR DOOR GLASS RUN |
Remove the rear door glass run.
12. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY |
Remove the 2 bolts, screw and rear door window division bar.
- NOTICE:
- Do not drop or damage the rear door window division bar when removing the bolts and screw.
13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
w/ Power window:
Remove the rear door glass from the rear door window regulator.
w/o Power window:
Remove the rear door glass from the rear door window regulator.
14. REMOVE REAR DOOR LOCK |
Using "Torx" socket wrench T30, remove the 3 screws.
- NOTICE:
- Do not drop or damage the rear door lock when removing the screws.
Move the rear door lock downward, remove the outside handle frame release plate and remove the rear door lock.
- HINT:
- Remove the rear door lock through the service hole.
Open the 2 covers.
Disconnect the rear door lock remote control cable and rear door inside locking cable.
Remove the door lock wire harness seal.