Dtc B1905/74 Short In Front Passenger Side Pretensioner Squib Circuit

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK FRONT PASSENGER SIDE FRONT SEAT OUTER BELT ASSEMBLY (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB)

CHECK CONNECTOR

CHECK NO. 2 FLOOR WIRE (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT)

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

1. Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (RAV4_ACA30 RM000000XFF05JX.html).
   
2. After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (RAV4_ACA30 RM000000XFF05JX.html).
   

1. Turn the ignition switch off.
   

2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
   

3. Disconnect the connectors from the front seat outer belt RH.
   

4. Connect SST (resistance 2.1 Ω) to connector C.
   

   CAUTION:

   Never connect a tester to the front seat outer belt (front passenger side front pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.

   NOTICE:

   1. Do not forcibly insert SST into the terminals of the connector when connecting.
      
   2. Insert SST straight into the terminals of the connector.
      

SST

09843-18061

5. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
   

6. Turn the ignition switch on (IG), and wait for at least 60 seconds.
   

7. Clear the DTCs (RAV4_ACA30 RM000000XFE06SX.html).
   

8. Turn the ignition switch off.
   

9. Turn the ignition switch on (IG), and wait for at least 60 seconds.
   

10. Check the DTCs (RAV4_ACA30 RM000000XFE06SX.html).
    

    OK:

    DTC B1905, B1906, B1907, B1908 or 74 is not output.
    

    HINT:

    DTCs other than DTC B1905, B1906, B1907, B1908 or 74 may be output at this time, but they are not related to this check.

1. Turn the ignition switch off.
   

2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
   

3. Disconnect SST from connector C.
   

4. Check that the floor wire connector (on the front seat outer belt RH side) is not damaged.
   

   OK:

   Lock button is not disengaged, or the claw of the lock is not deformed or damaged.
   

1. Disconnect the connectors from the center airbag sensor.
   

2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
   

3. Measure the voltage of the wire harness side connector.
   
   

   Standard voltage:

   for LHD:

   Tester Connection	Specified Condition
   L5-1 (R+) - Body ground	Below 1 V
   L5-2 (R-) - Body ground	Below 1 V

   for RHD:

   Tester Connection	Specified Condition
   K9-1 (L+) - Body ground	Below 1 V
   K9-2 (L-) - Body ground	Below 1 V

4. Turn the ignition switch off.
   

5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
   

6. Measure the resistance of the wire harness side connector.
   
   

   Standard resistance:

   for LHD:

   Tester Connection	Specified Condition
   L5-1 (R+) - L5-2 (R-)	Below 1 Ω
   L5-1 (R+) - Body ground	1 MΩ or higher
   L5-2 (R-) - Body ground	1 MΩ or higher

   for RHD:

   Tester Connection	Specified Condition
   K9-1 (L+) - K9-2 (L-)	Below 1 Ω
   K9-1 (L+) - Body ground	1 MΩ or higher
   K9-2 (L-) - Body ground	1 MΩ or higher

7. Release the activation prevention mechanism built into connector B (RAV4_ACA30 RM000000XFD06JX.html).
   

8. Measure the resistance of the wire harness side connector.
   
   

   Standard resistance:

   for LHD:

   Tester Connection	Specified Condition
   L5-1 (R+) - L5-2 (R-)	1 MΩ or higher

   for RHD:

   Tester Connection	Specified Condition
   K9-1 (L+) - K9-2 (L-)	1 MΩ or higher