Roof Headlining (For 5 Door) Removal

for Manual Seat Type:
Remove the rear No. 2 seat assembly (LandCruiser RM0000045DB008X.html).

for Power Seat Type:
Remove the rear No. 2 seat assembly (LandCruiser RM0000045DG00EX.html).

for Face to Face Seat Type:
Remove the rear No. 2 seat assembly (LandCruiser RM0000045DX006X.html).

for 60/40 Split Slide Walk-in Seat Type LH Side:
Remove the rear No. 1 seat assembly (LandCruiser RM00000468A00VX.html).

for 60/40 Split Slide Walk-in Seat Type RH Side:
Remove the rear No. 1 seat assembly (LandCruiser RM00000468F00QX.html).

for 60/40 Split Double-folding Seat Type LH Side:
Remove the rear No. 1 seatback assembly (LandCruiser RM00000468P00TX.html).

for 60/40 Split Double-folding Seat Type RH Side:
Remove the rear No. 1 seatback assembly (LandCruiser RM00000468U00WX.html).

Put protective tape around the door scuff plate.

Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

HINT:

Tape the screwdriver tip before use.

Remove the clip.

Detach the clip and claw and remove the cowl side trim board.

Remove the front door opening trim weatherstrip.

Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.

HINT:

Tape the screwdriver tip before use.

Remove the 2 bolts.

Detach the 2 claws and remove the No. 1 assist grip.

Detach the 3 guides and remove the front pillar garnish.

w/ Curtain Shield Airbag:
Protect the curtain shield airbag assembly.

1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.
   

   NOTICE:

   Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

   Text in Illustration

   *1	Curtain Shield Airbag Assembly
   *2	Adhesive Tape
   *3	Protective Cover

Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.

HINT:

Tape the screwdriver tip before use.

Remove the 2 bolts and quarter scuff plate.

Put protective tape around the rear door scuff plate.

Using a screwdriver, detach the 3 clips, 6 claws and 2 guides and remove the rear door scuff plate.

HINT:

Tape the screwdriver tip before use.

Remove the rear door opening trim weatherstrip.

Detach the 3 claws and remove the outer lap belt anchor cover.

Remove the bolt and disconnect the front seat outer belt floor anchor.

Detach the 4 claws and 2 clips and remove the lower center pillar garnish.

Using a screwdriver, detach the 2 claws and remove the front No. 2 assist grip plug.

HINT:

Tape the screwdriver tip before use.

Remove the 2 bolts.

Detach the 2 claws and remove the No. 2 assist grip.

Move the front shoulder belt anchor adjuster to the lowest position.

Remove the bolt.

Detach the 2 clips and 2 guides.

Pass the front seat outer belt floor anchor through the center pillar garnish and remove the center pillar garnish.

Remove the tonneau cover.

Detach the 4 claws and remove the cap.

Remove the bolt, luggage hold belt striker and front luggage compartment trim cover.

Detach the clip and remove the No. 1 deck board.

Detach the 5 clips and 4 claws and remove the rear floor mat rear support plate.

Remove the 3 bolts and floor side rail.

Detach the 4 claws and remove the rear floor carpet.

Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.

Remove the luggage compartment trim hook by turning it clockwise.

Using a screwdriver, detach the 2 claws and remove the No. 1 tonneau cover holder cap.

HINT:

Tape the screwdriver tip before use.

Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

HINT:

Tape the screwdriver tip before use.

Using a screwdriver, detach the 2 claws and remove the assist grip plug.

HINT:

Tape the screwdriver tip before use.

Remove the 2 bolts and assist grip.

w/o Rear No. 2 Seat:

1. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
   





2. Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.
   

3. Remove the 4 bolts and 2 screws.
   

4. Detach the 5 clips and 8 claws.
   





5. Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.
   
   

   
   
   
   

w/ Rear No. 2 Seat:

1. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
   





2. Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.
   

3. Remove the 2 bolts and 2 screws.
   





4. Detach the 4 clips and 8 claws and remove the deck trim side panel.
   
   

   
   
   
   

w/o Rear No. 2 Seat:

1. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
   





2. Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.
   

3. Remove the 4 bolts and screws.
   

4. Detach the 5 clips and 8 claws.
   

5. Disconnect each connector.
   





6. Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.
   
   

   
   
   
   

w/ Rear No. 2 Seat:

1. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
   





2. Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.
   

3. Remove the 2 bolts and screw.
   

4. Detach the 4 clips and 8 claws.
   





5. Disconnect each connector and remove the deck trim side panel.
   
   

   
   
   
   

Move the rear shoulder belt anchor adjuster to the lowest position.

Detach the 2 clips and 2 guides.

Pass the rear No. 1 seat outer belt floor anchor through the front quarter trim panel and remove the front quarter trim panel.

w/o Rear No. 2 Seat:

1. Detach the 7 clips and 2 guides and remove the rear quarter trim panel.
   

w/ Rear No. 2 Seat:

1. Detach the 7 clips and 2 guides.
   





2. Detach the 4 clips and 2 guides, pass the rear No. 2 seat outer belt floor anchor through the rear quarter trim panel and remove the rear quarter trim panel.
   

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.

Detach the 2 clips and remove the assist grip.

Remove the 2 clips from the vehicle body.

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.

Detach the 2 clips and remove the assist grip.

Remove the 2 clips from the vehicle body.

Using a screwdriver, detach the 4 claws and open the 2 covers.

HINT:

Tape the screwdriver tip before use.

Remove the 2 bolts and assist grip.

Detach the 4 claws and remove the visor bracket cover.

Remove the 2 screws and visor.

Turn the visor holder approximately 45° and pull it out as shown in the illustration.

Detach the 2 claws and remove the visor holder.

Detach the 4 clips.

Disconnect the connector and remove the map light.

Detach the 2 claws and remove the rain sensor cover.

Detach the 2 claws and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration.

Detach the 2 claws and remove the inner rear view mirror stay holder cover.

Remove the No. 1 room light assembly (LandCruiser RM000003MUN052X.html).

Remove the No. 2 room light assembly (LandCruiser RM000003MUN053X.html).

Detach the 7 claws and 4 clips and remove the television base.

Detach the 2 claws and remove the cooler plate.

Swing the bottom of the duct sideways and remove the duct.

Disconnect the connector.

Remove the 2 bolts and rear header speaker assembly.

w/ EC Mirror:
Disconnect the inner mirror connector.

w/ Rain Sensor:
Disconnect the rain sensor connector.

w/ Sliding Roof:
Disconnect the drive gear connector.

w/ Digital Audio Broadcasting Antenna:
Disconnect the connector and detach the wire harness clamp.

Disconnect the 2 connectors and detach the 3 clamps from the front pillar LH.

Remove the bolt.

Disconnect the 2 connectors and detach the 3 clamps from the front pillar RH.

Disconnect the 2 connectors and detach the clamp from the rear pillar LH.

Disconnect the connector and detach the 3 clamps from the rear pillar RH.

w/ Rear Seat Entertainment System:
Disconnect the 2 connectors.

w/o Sliding Roof:

1. Detach the 2 clips.
   

w/ Sliding Roof:

1. Detach the 2 clips, 2 guides and 8 fasteners.
   

   Text in Illustration

   *1	Guide
   *2	Fastener

w/ Rear Seat Entertainment System:

1. Detach the 2 clips, 2 guides and 6 fasteners.
   

   Text in Illustration

   *1	Guide
   *2	Fastener

Remove the roof headlining from the back door as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when removing it.

Detach the 5 claws of the front shoulder belt anchor plate and slide the front shoulder belt anchor plate in the direction of the arrow to remove it.

Detach the 6 claws of the rear shoulder belt anchor plate and slide the rear shoulder belt anchor plate in the direction of the arrow to remove it.

Detach the 3 clips.

Cut off the 3 clips and remove the roof side rail garnish.

Remove 3 clips from the vehicle body.

Detach the 4 claws and 2 guides and remove the roof side inner garnish cap.

Detach the claw and guide and remove the rear seat shoulder belt hanger.

Detach the 2 claws and remove the quarter trim cover.

Detach the 3 claws and 2 guides and remove the quarter trim jack cover.

Detach the 3 claws and 2 guides and remove the deck side trim cover.

Detach the 2 claws and remove the rear side rail spacer.

Detach the 2 claws and remove the rear No. 2 side rail spacer.

Detach the 2 claws and remove the rear No. 3 side rail spacer.