Rear Airbag Sensor (For 3 Door) -- Removal |
- HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (LandCruiser RM000003YMD00TX.html)
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).
| 2. REMOVE REAR NO. 1 SEAT ASSEMBLY |
for 60/40 Split Double-folding Seat Type LH Side:
Remove the rear No. 1 seat assembly (LandCruiser RM00000468P00TX.html).
for 60/40 Split Double-folding Seat Type RH Side:
Remove the rear No. 1 seat assembly (LandCruiser RM00000468U00WX.html).
for 60/40 Split Tumble Seat Type LH Side:
Remove the rear No. 1 seat assembly (LandCruiser RM0000046ZI006X.html).
for 60/40 Split Tumble Seat Type RH Side:
Remove the rear No. 1 seat assembly (LandCruiser RM0000046ZN006X.html).
for 60/40 Split Slide Walk-in Seat Type LH Side:
Remove the rear No. 1 seat assembly (LandCruiser RM00000468A00VX.html).
for 60/40 Split Slide Walk-in Seat Type RH Side:
Remove the rear No. 1 seat assembly (LandCruiser RM00000468F00QX.html).
| 3. REMOVE DOOR SCUFF PLATE ASSEMBLY LH |
 |
Put protective tape around the door scuff plate.
Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1 Protective Tape
| 4. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
 |
Remove the front door opening trim weatherstrip.
| 5. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Remove the tonneau cover.
| 6. REMOVE MAT SET PLATE COVER |
 |
- HINT:
- Use the same procedure for all mat set plate covers.
Using a screwdriver, detach the 2 claws and remove the mat set plate cover.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1 Protective tape
| 7. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE |
 |
Remove the 5 screws.
Detach the 6 claws and remove the rear floor mat rear support plate.
| 8. REMOVE QUARTER TRIM COVER HOLE LH |
 |
Detach the 2 claws and 2 guides and remove the quarter trim cover hole.
| 9. REMOVE REAR FLOOR CARPET ASSEMBLY |
 |
Remove the rear floor carpet.
| 10. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
 |
- HINT:
- Use the same procedure for the other No. 1 luggage compartment trim hook.
Remove the luggage compartment trim hook by turning it clockwise.
| 11. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover) |
 |
- HINT:
- Use the same procedure for the other tonneau cover holder cap.
Using a screwdriver, detach the 2 claws and remove the tonneau cover holder cap.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1 Protective tape
| 12. REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover) |
 |
- HINT:
- Use the same procedure for the other front deck side trim cover.
Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1 Protective tape
| 13. REMOVE OUTER LAP BELT COVER |
 |
- HINT:
- Use the same procedure for the other outer lap belt anchor cover.
Detach the 3 claws and remove the outer lap belt anchor cover.
| 14. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
 |
Remove the bolt and disconnect the front seat outer belt floor anchor.
Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
 |
Remove the 3 bolts and 2 screws.
Detach the 9 claws and 12 clips and remove the deck trim side panel.
| 15. REMOVE REAR AIRBAG SENSOR LH |
Remove the nut and rear airbag sensor.
 |
Disconnect the connector.