Steering Column Assembly (For Power Tilt And Power Telescopic Steering Column) Installation

Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.

Install the bolt.

Torque:

36 N*m{367 kgf*cm, 27 ft.*lbf}

Install the hole cover with the 4 bolts.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

NOTICE:

Do not fold back the boot part of the steering hole cover or extend it excessively. If it is extended excessively, return it to its original position.

Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft assembly.

HINT:

Install the steering intermediate shaft to the inside of the vehicle.

Install the bolt.

Torque:

36 N*m{367 kgf*cm, 27 ft.*lbf}

w/ KDSS:
Install the apron seal with the 7 clips.

w/o KDSS:
Install the apron seal with the 4 clips.

Align the matchmarks on the steering intermediate shaft, steering shaft stopper and steering column.

Install the steering column with the 4 nuts.

Torque:

26 N*m{265 kgf*cm, 19 ft.*lbf}

Install the bolts.

Torque:

36 N*m{367 kgf*cm, 27 ft.*lbf}

Attach the claws to install the wire harness protector and wire harness.

Using pliers, grip the claws of the clamp and install the combination switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

Connect the connectors to the combination switch with spiral cable.

Attach the claw to install the switch.

Connect the switch connector.

Attach the claw to install the steering column upper cover.

Attach the 4 clips to install the steering column upper cover to the instrument cluster finish panel.

Attach the 2 claws to install the steering column lower cover.

NOTICE:

Do not damage the tilt and telescopic switch.

Install the 3 screws.

Check the check window shown in the illustration.

HINT:

When the spiral cable sub-assembly is centered, the connector is at the top and the conditions below can be checked.

1. w/o Steering Heater:
   With the steering wheel straight ahead, align the matchmarks to check the colored roller from the check window.
   
2. w/ Steering Heater:
   With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.
   

Text in Illustration

*A	w/o Steering Heater	*B	w/ Steering Heater
*C	for Type A	*D	for Type B
*a	Check Window	*b	Matchmark
	Colored Roller		U-turn Point

If the spiral cable sub-assembly is not centered, center it.

Rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

CAUTION:

Do not turn the spiral cable sub-assembly using the airbag wire harness.

Rotate the spiral cable sub-assembly 2.5 times clockwise from the lock position to align the matchmarks and check the check window.

HINT:

1. The spiral cable sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.
   
2. When the spiral cable sub-assembly is centered, the connector is at the top and the conditions below can be checked.
   

1. w/o Steering Heater:
   With the steering wheel straight ahead, align the matchmarks to check the colored roller from the check window.
   
2. w/ Steering Heater:
   With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.
   

Text in Illustration

*A	w/o Steering Heater	*B	w/ Steering Heater
*C	for Type A	*D	for Type B
*a	Check Window	*b	Matchmark
	Colored Roller		U-turn Point