Stabilizer Control Valve (W/ Kdss) Removal


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  2. REMOVE SIDE STEP ASSEMBLY LH

  3. REMOVE STABILIZER CONTROL VALVE PROTECTOR

  4. DRAIN SUSPENSION FLUID

  5. DISCONNECT FRONT NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

  6. DISCONNECT REAR NO. 1 STABILIZER CONTROL TUBE ASSEMBLY

  7. REMOVE STABILIZER CONTROL WITH ACCUMULATOR HOUSING ASSEMBLY

Stabilizer Control Valve (W/ Kdss) -- Removal



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (LandCruiser RM000003YMD00TX.html).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (LandCruiser RM000003YMF011X.html).


2. REMOVE SIDE STEP ASSEMBLY LH

  1. w/ Illumination:
    Disconnect the 2 connectors.



  1. Remove the 6 bolts and side step.


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155.Suspension Control.Air Suspension System.Stabilizer Control Valve (W/ Kdss) Removal



3. REMOVE STABILIZER CONTROL VALVE PROTECTOR


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Remove the 2 bolts and stabilizer control valve protector.



4. DRAIN SUSPENSION FLUID


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Loosen the bleeder plug on the stabilizer control with accumulator housing assembly and drain suspension fluid.

    HINT:
    1. Drain suspension fluid when performing operations related to the hydraulic circuits.
    2. Draining suspension fluid decreases suspension fluid pressure.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{85 kgf*cm, 73 in.*lbf}


5. DISCONNECT FRONT NO. 1 STABILIZER CONTROL TUBE ASSEMBLY


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using a union nut wrench, disconnect the 2 flare nuts from the stabilizer control with accumulator housing to disconnect the front No. 1 stabilizer control tube assembly.



6. DISCONNECT REAR NO. 1 STABILIZER CONTROL TUBE ASSEMBLY


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Using a union nut wrench, disconnect the 2 flare nuts from the stabilizer control with accumulator housing.

  1. Remove the 2 bolts and disconnect the rear No. 1 stabilizer control tube assembly.



7. REMOVE STABILIZER CONTROL WITH ACCUMULATOR HOUSING ASSEMBLY


    Land Cruiser, Land Cruiser Prado. Grj150 Trj150,155 Kdj150,155 Lj150, Gdj150,155

  1. Disconnect the connector, and then detach the clamp from the sensor bracket.

  1. Remove the 3 bolts and stabilizer control with accumulator housing.

    NOTICE:
    Do not disassemble the stabilizer control with accumulator housing assembly or expose it to an open flame as the accumulator of the stabilizer control with accumulator housing assembly contains gas.