Dtc C2177/77 Initialization Not Completed

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK FREQUENCY RECEIVING CONDITION

PERFORM INITIALIZATION

CONFIRM TIRE INFLATION PRESSURE (DATA LIST)

DESCRIPTION

1. The tire pressure warning ECU and receiver is replaced.
   
2. A tire pressure warning valve and transmitter is replaced.
   
3. Tires with a different tire standard pressure are installed.
   
4. The tires are rotated.
   
5. A new vehicle is delivered.
   

WIRING DIAGRAM

INSPECTION PROCEDURE

NOTICE:

1. When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
   
2. It is necessary to perform initialization (LandCruiser RM000000XMZ0AOX.html) after registration (LandCruiser RM000000XN10DCX.html) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.
   

1. Check that the vehicle is not located in an area such as described below:
   

   1. Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
      

      HINT:

      If the vehicle is located in an area such as the one described above, the tire pressure warning light may come on after blinking 1 minute only in a particular area due to interfering radio frequencies.

   2. Devices using similar radio frequencies are used in the vehicle.
      

      OK:

      Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.
      

      HINT:

      Radio transmissions may be interrupted due to the surroundings or devices installed by the user.

1. Perform initialization (LandCruiser RM000000XMZ0AOX.html).
   

1. Turn the ignition switch off.
   

2. Connect the GTS to the DLC3.
   

3. Turn the ignition switch ON.
   

4. Turn the GTS on.
   

5. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
   

6. Check the values by referring to the table below.
   
   

   Tire Pressure Monitor

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   ID 1 Tire Inflation Pressure	ID1 tire inflation pressure/ min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*1
   ID 2 Tire Inflation Pressure	ID2 tire inflation pressure/ min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*1
   ID 3 Tire Inflation Pressure	ID3 tire inflation pressure/ min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*1
   ID 4 Tire Inflation Pressure	ID4 tire inflation pressure/ min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*1
   ID 5 Tire Inflation Pressure*2	ID5 tire inflation pressure/ min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*1

   HINT:

   1. *1: It may take a few minutes until the values are displayed.
      
   2. *2: w/ Spare Tire
      
   3. When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.
      
   4. The wheel position cannot be determined from ID1 through ID4 or ID1 through ID5 (w/ Spare Tire) on the Data List.
      
   
   

   Result:

   
   

   Result	Proceed to
   All tire pressure readings are equal to specified values.	A
   Tire pressure values are not displayed.	B