Rear View Monitor System (For Radio And Display Type) Reverse Signal Circuit

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK VEHICLE SIGNAL (OPERATION CHECK)

CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)

DESCRIPTION

1. *1: for Automatic Transmission
   
2. *2: for Manual Transmission
   

WIRING DIAGRAM

INSPECTION PROCEDURE

1. Enter the "Function Check/Setting I" mode and select "Vehicle Signal" (HILUX_TGN26 RM0000043X902VX.html).
   

2. Check that the display changes between ON and OFF according to the shift lever position.
   

   OK:

   Shift Lever Position	Display
   R	ON
   Except R	OFF

   HINT:

   This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.

1. Disconnect the G127 radio and display receiver assembly connector.
   

2. Measure the voltage according to the value(s) in the table below.
   

   Standard Voltage:

   Tester Connection	Condition	Specified Condition
   G127-2 (REV) - Body ground	Ignition switch ON, shift lever in R	7.5 to 14 V
   G127-2 (REV) - Body ground	Ignition switch ON, shift lever not in R	Below 1 V

   Text in Illustration

   *a	Front view of wire harness connector (to Radio and Display Receiver Assembly)

   Result

   Result	Proceed to
   OK	A
   NG (for Automatic Transmission)	B
   NG (for Manual Transmission)	C

1. Disconnect the G127 radio and display receiver assembly connector.
   

2. Disconnect the C57 park/neutral position switch assembly connector.
   

3. Measure the resistance according to the value(s) in the table below.
   

   Standard Resistance:

   Tester Connection	Condition	Specified Condition
   G127-2 (REV) - C57-1 (RL)	Always	Below 1 Ω
   G127-2 (REV) - Body ground	Always	10 kΩ or higher

   Result

   Result	Proceed to
   OK (for A340F)	A
   OK (for A343E)	B
   OK (for A343F)	C
   NG	D

1. Disconnect the G127 radio and display receiver assembly connector.
   

2. Disconnect the C87*1, C27*2 or C165*3 back-up light switch assembly connector.
   

   1. *1: for 2TR-FBE, 2TR-FE
      
   2. *2: for 1KD-FTV
      
   3. *3: for 1KD-FTV, i-ART
      

3. Measure the resistance according to the value(s) in the table below.
   
   

   Standard Resistance:

   for 2TR-FBE, 2TR-FE:

   Tester Connection	Condition	Specified Condition
   G127-2 (REV) - C87-1	Always	Below 1 Ω
   G127-2 (REV) - Body ground	Always	10 kΩ or higher

   for 1KD-FTV:

   Tester Connection	Condition	Specified Condition
   G127-2 (REV) - C27-1	Always	Below 1 Ω
   G127-2 (REV) - Body ground	Always	10 kΩ or higher

   for 1KD-FTV, i-ART:

   Tester Connection	Condition	Specified Condition
   G127-2 (REV) - C165-1	Always	Below 1 Ω
   G127-2 (REV) - Body ground	Always	10 kΩ or higher

   Result

   Result	Proceed to
   OK (for R150/R151)	A
   OK (for R150F/R151F/R156F)	B
   NG	C