Rear View Monitor System (For Navigation Receiver Type) Reverse Signal Circuit

Audio Visual Telematics. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
Park Assist Monitoring. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK VEHICLE SIGNAL (OPERATION CHECK)

CHECK NAVIGATION RECEIVER ASSEMBLY

CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)

REAR VIEW MONITOR SYSTEM (for Navigation Receiver Type) - Reverse Signal Circuit


DESCRIPTION

The navigation receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission

WIRING DIAGRAM


Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Park Assist Monitoring.Rear View Monitor System (For Radio And Display Type).Rear View Monitor System (For Navigation Receiver Type) Reverse Signal Circuit


INSPECTION PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Park Assist Monitoring.Rear View Monitor System (For Radio And Display Type).Rear View Monitor System (For Navigation Receiver Type) Reverse Signal Circuit

  1. Enter the "Function Check/Setting" screen and select "Connection status" (HILUX_TGN26 RM000003A3N01WX.html).

  1. Check that the display changes between ON and OFF according to the shift lever position.

    OK:
    Shift Lever Position
    		Display
    R
    		High
    Except R
    		Low
    HINT:
    This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.


NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (HILUX_TGN26 RM00000140008LX.html)

2.CHECK NAVIGATION RECEIVER ASSEMBLY
Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Park Assist Monitoring.Rear View Monitor System (For Radio And Display Type).Rear View Monitor System (For Navigation Receiver Type) Reverse Signal Circuit

  1. Disconnect the G152 navigation receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    G152-2 (REV) - Body ground
    		Ignition switch ON, shift lever in R
    		7.5 to 14 V
    G152-2 (REV) - Body ground
    		Ignition switch ON, shift lever not in R
    		Below 1 V
    Text in Illustration
    *a
    		Front view of wire harness connector
    (to Navigation Receiver Assembly)
    Result
    Result
    		Proceed to
    OK
    		A
    NG (for Automatic Transmission)
    		B
    NG (for Manual Transmission)
    		C


B
Go to step 3

C
Go to step 4
A

REPLACE NAVIGATION RECEIVER ASSEMBLY (HILUX_TGN26 RM000003O1L003X.html)

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

  1. Disconnect the G152 navigation receiver assembly connector.

  1. Disconnect the C26 park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    G152-2 (REV) - C26-1 (RL)
    		Always
    		Below 1 Ω
    G152-2 (REV) - Body ground
    		Always
    		10 kΩ or higher
    Result
    Result
    		Proceed to
    OK (for A340F)
    		A
    OK (for A343E)
    		B
    OK (for A343F)
    		C
    NG
    		D


B
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (HILUX_TGN26 RM0000010NC05PX.html)

C
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (HILUX_TGN26 RM0000010NC05LX.html)

D
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (HILUX_TGN26 RM0000010NC05IX.html)

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)

  1. Disconnect the G152 navigation receiver assembly connector.

  1. Disconnect the C27 back-up light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    G152-2 (REV) - C27-1
    		Always
    		Below 1 Ω
    G152-2 (REV) - Body ground
    		Always
    		10 kΩ or higher
    Result
    Result
    		Proceed to
    OK (for R151)
    		A
    OK (for R151F)
    		B
    NG
    		C


B
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (HILUX_TGN26 RM0000046SW00AX.html)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (HILUX_TGN26 RM0000046SW009X.html)