Dtc P0607 Control Module Performance

Engine Hybrid System. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
1Gr-Fe Engine Control. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

DESCRIPTION

CONFIRMATION DRIVING PATTERN

INSPECTION PROCEDURE

CHECK FOR DTC

DTC P0607 Control Module Performance


DESCRIPTION

The ECM continuously monitors its main and sub CPUs. This self-check ensures that the ECM is functioning properly. If outputs from the CPUs are different and deviate from the standard, the ECM illuminates the MIL and stores a DTC immediately.

DTC Code
DTC Detection Condition
Trouble Area
P0607
When either condition below is met (1 trip detection logic):
  1. An ECM main CPU error.
  2. An ECM sub CPU error.
ECM

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the tester off.
  5. Turn the ignition switch off.
  6. Disconnect the tester.
  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  8. Connect the cable to the negative (-) battery terminal.
  9. Connect the tester to the DLC3.
  10. Turn the ignition switch to ON and turn the tester on.
  11. Wait 16 seconds or more.
  12. Enter the following menus: Powertrain / Engine and ECT / DTC.
  13. Read the pending DTCs.
    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.
  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P0607.
  16. Check the DTC judgment result.

    Tester Display
    		Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.CHECK FOR DTC

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTC (HILUX_TGN26 RM000000PDK12JX.html).

  1. Turn the ignition switch off and turn the tester off.

  1. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Wait 16 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Check for DTC.

    OK:
    P0607 is not output.


NG
REPLACE ECM (HILUX_TGN26 RM000000VW202SX.html)
OK

CHECK FOR INTERMITTENT PROBLEMS (HILUX_TGN26 RM000000PDQ0YKX.html)