Dtc P0627 Fuel Pump Control Circuit / Open

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

INSPECT FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

CHECK WHETHER DTC OUTPUT RECURS (DTC P0627)

REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

BLEED AIR FROM FUEL SYSTEM

PERFORM FUEL SUPPLY PUMP INITIALIZATION

REPLACE ECM

REPAIR OR REPLACE HARNESS OR CONNECTOR

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

DESCRIPTION

HINT:

1. For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (HILUX_TGN26 RM0000012WW02QX.html).
   
2. When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Press.
   Under a stable operating condition such as idling, Fuel Press is within 5000 kPa of Target Common Rail Pressure.
   

WIRING DIAGRAM

INSPECTION PROCEDURE

NOTICE:

1. After replacing the ECM, the new ECM needs registration (HILUX_TGN26 RM0000012XK043X.html) and initialization (HILUX_TGN26 RM000000TIN04FX.html).
   
2. After replacing the fuel supply pump assembly, the ECM needs initialization (HILUX_TGN26 RM000000TIN04FX.html).
   

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1. Disconnect the suction control valve connector.
   

   Text in Illustration

   *1	Fuel Supply Pump Assembly
   *2	Suction Control Valve

2. Measure the resistance of the suction control valve.
   

   OK:

   No open or short circuit malfunction.
   

1. Disconnect the suction control valve connector.
   

2. Disconnect the ECM connector.
   

3. Measure the resistance according to the value(s) in the table below.
   
   

   Standard Resistance:

   
   

   Tester Connection	Condition	Specified Condition
   C5-1 - C22-2 (PCV+)	Always	Below 1 Ω
   C5-2 - C22-1 (PCV-)	Always	Below 1 Ω
   C5-1 or C22-2 (PCV+) - Body ground	Always	10 kΩ or higher
   C5-2 or C22-1 (PCV-) - Body ground	Always	10 kΩ or higher

4. Reconnect the suction control valve connector.
   

5. Reconnect the ECM connector.
   

1. Connect the intelligent tester to the DLC3
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Clear the DTCs (HILUX_TGN26 RM000000PDK0TAX.html).
   

4. Start the engine and idle it for 1 second or more.
   

5. Enter the following menus: Powertrain / Engine and ECT / DTC.
   

6. Read the DTCs.
   

   Result

   Result	Proceed to
   No DTC is output	A
   P0627 is output	B

1. Replace the fuel supply pump assembly (HILUX_TGN26 RM0000014FO01CX.html).
   

1. Bleed the air from the fuel system (HILUX_TGN26 RM000002SY8026X_01_0002.html).
   

1. Perform fuel supply pump initialization (HILUX_TGN26 RM000000TIN04FX.html).
   

1. Replace the ECM (HILUX_TGN26 RM0000043H100GX.html).
   

1. Repair or replace the harness or connector.
   

1. Connect the intelligent tester to the DLC3.
   

2. Clear the DTCs (HILUX_TGN26 RM000000PDK0TAX.html).
   

3. Turn the ignition switch off for 30 seconds or more.
   

4. Start the engine and idle it for 1 second or more.
   

5. Confirm that the DTC is not output again.