Engine Assembly Installation

Install 2 engine hangers with 2 bolts.

Torque:

42 N*m{428 kgf*cm, 31 ft.*lbf}

HINT:

Attach an engine sling device and hang the engine with a chain block.

NOTICE:

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

Lift the engine and remove it from the engine stand.

NOTICE:

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

Place the engine onto a workbench.

Attach the engine sling device and chain block to the engine hangers.

Text in Illustration

Lower

Slowly lower the engine assembly into the engine compartment.

Install the engine mounting brackets with the 4 bolts and 4 nuts.

Torque:

38 N*m{388 kgf*cm, 28 ft.*lbf}

Remove the 2 bolts and 2 engine hangers.

Install the end plate with the bolt.

Torque:

18 N*m{184 kgf*cm, 13 ft.*lbf}

Connect the No. 1 water by-pass pipe to the rear end plate with the bolt.

Torque:

18 N*m{178 kgf*cm, 13 ft.*lbf}

Using SST, hold the crankshaft.

SST

09213-54015(91651-60855)
09330-00021

Install the front spacer, drive plate and rear spacer to the crankshaft.

Text in Illustration

*1	Front Drive Plate Spacer
*2	Drive Plate and Ring Gear
*3	Rear Drive Plate Spacer
	Transmission Side

HINT:

1. The front drive plate spacer is reversible.
   
2. As the rear drive plate spacer and drive plate and ring gear are not reversible, be sure to install it so that it is facing in the direction shown in the illustration.
   

Clean the bolts and bolt holes.

Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

Install and uniformly tighten the 10 bolts in several steps in the sequence shown in the illustration.

Torque:

74 N*m{755 kgf*cm, 55 ft.*lbf}

NOTICE:

Do not start the engine for at least an hour after installing the drive plate.

Check the drive plate for damage.

Set up a dial indicator and measure the runout of the 6 portions around the torque converter contact surfaces.

Maximum runout:

0.30 mm (0.0118 in.)

Using SST, hold the crankshaft.

SST

09213-54015(91651-60855)
09330-00021

Clean the bolts and bolt holes.

Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

Install the flywheel with the 10 bolts and uniformly tighten the bolts in several steps in the sequence shown in the illustration.

Torque:

27 N*m{270 kgf*cm, 20 ft.*lbf}

Mark the top of the bolts with paint.

Tighten the 10 bolts 90° in the same sequence.

Check that the paint marks are now at a 90° angle to the top.

Insert SST into the clutch disc. Then insert SST (together with the clutch disc) into the flywheel.

SST

09301-00110

NOTICE:

Be sure to install the clutch disc so that it is facing in the correct direction.

Align the matchmarks on the clutch cover and flywheel.

Tighten the 6 bolts as described below.

1. Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.
   

2. Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.
   

Lightly move SST up and down, and right and left.

SST

09301-00110

Check that the disc is in the center, and then tighten the bolts.

Torque:

19 N*m{195 kgf*cm, 14 ft.*lbf}

Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

Maximum misalignment:

0.5 mm (0.020 in.)

1. If the misalignment is more than the maximum, use SST to adjust the diaphragm spring tip alignment.
   

SST

09333-00013

Install the 4 bolts and rear No. 1 engine mounting insulator.

Torque:

47 N*m{479 kgf*cm, 35 ft.*lbf}

Install the starter with the 2 bolts.

Torque:

37 N*m{377 kgf*cm, 27 ft.*lbf}

Install the starter wire to the terminal 30 with the nut.

Torque:

9.8 N*m{100 kgf*cm, 87 in.*lbf}

Connect the terminal cap.

Connect the starter connector.

Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange and transfer flange.

Align the matchmarks on the propeller shaft flange and transfer flange.

Install the propeller shaft with the 4 nuts and 4 washers.

Torque:

88 N*m{899 kgf*cm, 65 ft.*lbf}

Temporarily install the center support bearing bracket with the 2 plates and 2 bolts. Tighten the bolts as much as possible by hand.

Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange and differential flange.

Align the matchmarks on the propeller shaft flange and differential flange.

Connect the propeller shaft with the 4 bolts, 4 washers and 4 nuts.

Torque:

88 N*m{899 kgf*cm, 65 ft.*lbf}

Unload the vehicle. The center lines of the center bearing and center bearing housing (refer to the illustration) must be adjusted so that they are within 0 +/-1 mm (0 +/-0.0394 in.) of each other. Measure the difference along the front/rear axis of the vehicle.

Distance (A):

0 +/-1 mm (0 +/-0.0394 in.)

Tighten the 2 bolts of the center support bearing bracket.

Torque:

36 N*m{369 kgf*cm, 27 ft.*lbf}

Remove SST from the extension housing.

Install the propeller shaft to the extension housing.

Temporarily install the center support bearing bracket with the 2 plates and 2 bolts. Tighten the bolts as much as possible by hand.

Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange and differential flange.

Align the matchmarks on the propeller shaft flange and differential flange.

Connect the propeller shaft with the 4 bolts, 4 washers and 4 nuts.

Torque:

88 N*m{899 kgf*cm, 65 ft.*lbf}

Unload the vehicle. The center lines of the center bearing and center bearing housing (refer to the illustration) must be adjusted so that they are within 0 +/-1 mm (0 +/-0.0394 in.) of each other. Measure the difference along the front/rear axis of the vehicle.

Distance (A):

0 +/-1 mm (0 +/-0.0394 in.)

Tighten the 2 bolts of the center support bearing bracket.

Torque:

36 N*m{369 kgf*cm, 27 ft.*lbf}

Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange and transfer flange.

Align the matchmarks on the propeller shaft flange and transfer flange.

Install the propeller shaft with the 4 nuts and 4 washers.

Torque:

88 N*m{899 kgf*cm, 65 ft.*lbf}

Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange and differential flange.

Align the matchmarks on the propeller shaft flange and differential flange.

Connect the propeller shaft with the 4 bolts, 4 nuts and 4 washers.

Torque:

88 N*m{899 kgf*cm, 65 ft.*lbf}

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

40 mm (1.57 in.)

Install the front exhaust pipe to the exhaust pipe support.

Using a plastic-faced hammer and wooden block, tap on a new gasket until its surface is flush with the exhaust manifold.

NOTICE:

1. Be sure to install the gasket so that it faces the correct direction.
   
2. Do not reuse the gasket.
   
3. Do not damage the gasket.
   
4. When connecting the exhaust pipe, do not push in the gasket with the exhaust pipe.
   

Connect the front exhaust pipe to the exhaust manifold with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

Torque:

43 N*m{438 kgf*cm, 32 ft.*lbf}

Install a new gasket and connect the front exhaust pipe to the center exhaust pipe with the 2 bolts and 2 nuts.

Torque:

48 N*m{489 kgf*cm, 35 ft.*lbf}

Connect the heated oxygen sensor connector and attach the wire harness clamp.

Connect the air fuel ratio sensor connector and attach the wire harness clamp.

Install the hood with the 4 bolts.

Torque:

13 N*m{133 kgf*cm, 10 ft.*lbf}

Connect the washer nozzle hose.

Adjust the hood (HILUX_TGN26 RM00000138K01ZX.html).

Temporarily install the compressor with the bolt labeled A.

Install the compressor completely by tightening the 4 bolts in the order shown in the illustration.

Torque:

25 N*m{250 kgf*cm, 18 ft.*lbf}

NOTICE:

In order to prevent misalignment, which causes belt rattle, tightening of the bolts must be performed in the order shown.

Connect the compressor connector.

Install the suction hose with the bolt.

Torque:

5.4 N*m{55 kgf*cm, 48 in.*lbf}

Install a new O-ring and the engine oil level dipstick guide with the bolt.

Torque:

8.0 N*m{82 kgf*cm, 71 in.*lbf}

Connect the vane pump with the 2 bolts.

Torque:

21 N*m{214 kgf*cm, 15 ft.*lbf}

Connect the oil pressure switch connector.

Connect the wire clamp to the front engine mounting bracket LH with the bolt.

Torque:

13 N*m{128 kgf*cm, 9 ft.*lbf}

Connect the 2 engine room junction block connectors and wire clamp.

Connect the cable to the engine room junction block with the nut.

Torque:

13 N*m{133 kgf*cm, 10 ft.*lbf}

Install the engine room relay block cover (side).

Install the engine room relay block cover (upper).

Connect the ground wire with the nut.

Torque:

31 N*m{316 kgf*cm, 23 ft.*lbf}

Connect the ground wire to the left side of the frame with the bolt so that it is within the range shown in the illustration.

Torque:

31 N*m{316 kgf*cm, 23 ft.*lbf}

Connect the sensor bracket to the right side of the frame with the bolt.

Torque:

13 N*m{133 kgf*cm, 10 ft.*lbf}

Connect the air fuel ratio sensor connector.

Push the engine wire through the dash panel into the cabin.

HINT:

The wire should be within the range shown in the illustration.

Connect the air injection driver connector.

Connect the ECM connectors.

1. Connect the 4 ECM connectors.
   

2. Install the glove compartment door.
   

Connect the fuel hose.

Connect the No. 2 fuel hose.

Connect the No. 1 fuel hose (HILUX_TGN26 RM000000YL401YX.html).

Connect the No. 4 air injection system hose to the air switching valve.

Secure the hose with the clamp.

Connect the vacuum hose (for the brake master cylinder).

Connect the purge line hose.

Connect the heater water inlet hose and heater water outlet hose to the heater pipe.

Install the radiator with the 4 bolts.

Torque:

12 N*m{122 kgf*cm, 9 ft.*lbf}

w/ Airbag System:

1. Attach the 4 clamps to the radiator.
   

Connect the oil cooler inlet hose to the radiator.

Connect the oil cooler outlet hose to the radiator.

Install the fan pulley to the engine water pump.

Place the shroud together with the fluid coupling fan between the radiator and engine.

NOTICE:

Be careful not to damage the radiator core.

Install the coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.

Attach the shroud's claws to the radiator as shown in A in the illustration.

Install the fan shroud with the 2 bolts.

Torque:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Connect the reservoir hose to the radiator tank upper.

Install the fan and generator V belt (HILUX_TGN26 RM000000YMN02DX.html).

Tighten the 4 nuts of the fluid coupling fan.

Torque:

25 N*m{255 kgf*cm, 18 ft.*lbf}

Connect the air pump inlet to the radiator with the bolt.

Torque:

8.5 N*m{87 kgf*cm, 75 in.*lbf}

Install the fan and generator V belt to all the pulleys except the V-ribbed belt tensioner pulley.

Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward, and then install the fan and generator V belt to the tensioner pulley.

NOTICE:

1. The backside of the fan and generator V belt should face the tensioner pulley.
   
2. Check that the fan and generator V belt is properly installed to each pulley.
   

Connect the radiator hose outlet to the radiator.

Connect the radiator hose inlet to the radiator.

Attach the 6 claws to install the radiator grille.

Install the 2 screws and 2 clips.

Install the air cleaner and intake air connector assembly with the 4 bolts, and tighten the hose clamp.

Torque:

for air cleaner:

14 N*m{143 kgf*cm, 10 ft.*lbf}

for intake air connector:

8.0 N*m{82 kgf*cm, 71 in.*lbf}

for hose clamp:

5.0 N*m{51 kgf*cm, 44 in.*lbf}

Connect the mass air flow meter connector and attach the wire harness clamps.

Connect the No. 2 PCV hose.

Connect the vacuum hose.

Add fresh engine oil.

Standard Oil Grade:

Oil Grade	Oil Viscosity (SAE)
API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil	5W-30 10W-30 (5W-30 is the best choice for good fuel economy and good starting in cold weather)
API grade SL, SM or SN multigrade engine oil	15W-40 20W-50

Standard Capacity:

Item	Capacity
Drain and refill without oil filter change	5.3 liters (5.6 US qts, 4.7 Imp. qts)
Drain and refill with oil filter change	5.6 liters (5.9 US qts, 4.9 Imp. qts)
Dry fill	6.3 liters (6.7 US qts, 5.5 Imp. qts)

Install the oil filler cap.

Tighten all the plugs and fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

Torque:

for Cylinder block drain cock plug:

13 N*m{130 kgf*cm, 9 ft.*lbf}

Standard Capacity:

Item	Specified Condition
A/T	8.1 liters (8.6 US qts, 7.1 Imp. qts)
M/T	7.8 liters (8.2 US qts, 6.9 Imp. qts)

NOTICE:

Never use water as a substitute for engine coolant.

HINT:

1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
   
2. Please contact your TOYOTA dealer for further details.
   

Fill the radiator reservoir with TOYOTA SLLC to the F line.

Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the F line, add TOYOTA SLLC to the F line.

Install the radiator cap.

Bleed air from the cooling system.

1. Warm up the engine until the thermostat opens.
   While the thermostat is open, circulate the coolant for several minutes.
   

2. Maintain the engine speed at 2500 to 3000 rpm.
   

3. Press the inlet and outlet radiator hoses several times by hand to bleed air.
   

   CAUTION:

   When pressing the radiator hoses:

   1. Wear protective gloves.
      
   2. Be careful as the radiator hoses are hot.
      
   3. Keep your hands away from the radiator fan.
      

Stop the engine and wait until the coolant cools down to ambient temperature.

CAUTION:

Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

Check the coolant level in the radiator reservoir.
If the coolant level is below the L line, add SLLC up to the reservoir F line.

Make sure that there are no fuel leaks after performing maintenance on the fuel system.

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the intelligent tester on.
   

   NOTICE:

   Do not start the engine.

3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
   

4. Check that there are no leaks from the fuel system.
   If there are fuel leaks, repair or replace parts as necessary.
   

5. Turn the ignition switch off.
   

6. Disconnect the intelligent tester from the DLC3.
   

Start the engine.

NOTICE:

Perform the inspection while the engine is cold.

The fuel pump operates only for a calculated time when the coolant temperature is 20°C (68°F) or less and learned ethanol concentration is 85% or more.

Check for fuel leaks.

1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
   

Start the engine, and check that there are no oil leaks after performing maintenance.

Fill the radiator with coolant and attach a radiator cap tester.

Warm up the engine.

Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm², 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the cylinder block and cylinder head.

Warm up and stop the engine.

When using the intelligent tester:

1. Connect the intelligent tester to the DLC3.
   

   NOTICE:

   Switch off all the accessories and the A/C before connecting the intelligent tester.

2. Start the engine and idle it.
   

3. Turn the intelligent tester main switch on.
   

4. Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
   

   Standard ignition timing:

   0 to 20° BTDC @ idle
   

   NOTICE:

   When checking the ignition timing, the transmission should be in neutral or park.

   HINT:

   Refer to the intelligent tester operator's manual for further details.

5. Check that the ignition timing advances immediately when the engine speed is increased.
   

6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
   

7. Monitor IGN Advance.
   

8. Perform the Active Test.
   

   Standard ignition timing:

   3 to 7° BTDC @ idle
   

   NOTICE:

   When checking the ignition timing, the transmission should be in neutral or park.

   HINT:

   Refer to the intelligent tester operator's manual for further details.

When not using the intelligent tester:

1. Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.
   

   SST

   09843-18030
   

   Text in Illustration

   *a	Front view of DLC3

   NOTICE:

   1. Confirm the terminal number before connecting the probe. Connecting the wrong terminals can damage the engine.
      
   2. Turn off all electrical systems before connecting the probe.
      

2. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
   

3. Start the engine and idle it.
   





4. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
   

   SST

   09843-18040
   

   Text in Illustration

   *a	Front view of DLC3

   NOTICE:

   When checking the ignition timing, the transmission should be in neutral.

   
   

   HINT:

   1. After connecting terminals TC and CG, the engine speed changes to between approximately 1000 and 1500 rpm for 5 seconds, and then returns to idle as the ECM checks that the ISC (Idle Speed Control) system operates properly.
      
   2. Inspect the ignition timing after the engine speed returns to idle.
      

   Text in Illustration

   *a	Engine Speed
   *b	Approx. 1000 to 1500 rpm
   *c	Idle Speed
   *d	5 sec.
   *e	Connect Terminals TC and CG

5. Using the timing light, measure the ignition timing.
   

   Standard ignition timing:

   3 to 7° BTDC @ idle
   

   NOTICE:

   1. Turn all the electrical systems and the A/C off.
      
   2. When checking the ignition timing, the transmission should be in neutral or park.
      

6. Remove SST from the DLC3.
   

7. Check the ignition timing.
   

   Standard ignition timing:

   0 to 20° BTDC @ idle
   

8. Confirm that the ignition timing advances immediately when the engine speed is increased.
   

9. Turn the ignition switch off.
   

10. Disconnect the timing light from the engine.
    

Warm up and stop the engine.

When using the intelligent tester:

1. Connect the intelligent tester to the DLC3.
   

   NOTICE:

   Switch off all accessories and the air conditioning before connecting the intelligent tester.

2. Start the engine and idle it.
   

3. Turn the intelligent tester on.
   

4. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine SPD.
   

   Standard idle speed:

   600 to 700 rpm
   

   NOTICE:

   When checking the idle speed, the transmission should be in neutral.

   HINT:

   Refer to the intelligent tester operator's manual for further details.

5. Turn the ignition switch off.
   

6. Disconnect the intelligent tester from the DLC3.
   

When not using the intelligent tester:

1. Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.
   

   SST

   09843-18030
   

   Text in Illustration

   *a	Front view of DLC3

2. Start the engine and idle it.
   

3. Check the idle speed.
   

   Standard idle speed:

   600 to 700 rpm
   

Start and warm up the engine.

Run the engine at 2500 rpm for approximately 180 seconds, and then idle the engine.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe.

Check the CO/HC concentration at idle.

Standard idle CO concentration:

0 to 0.5%

Standard idle HC concentration:

Refer to applicable local regulation

If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.

1. Check the air fuel ratio sensor (HILUX_TGN26 RM000001421010X.html) and heated oxygen sensor operation (HILUX_TGN26 RM00000159K00JX.html).
   

2. See the table below for possible causes, and then inspect and repair the applicable causes if necessary.
   
   

   CO	HC	Problems	Causes
   Normal	High	Rough idle	Faulty ignition: Incorrect timing Fouled, shorted or improperly gapped plugs Incorrect valve clearance Leaks in intake and exhaust valves Leaks in cylinders
   Low	High	Rough idle (Fluctuating HC reading)	Vacuum leaks: PCV hoses Intake manifold Throttle body Brake booster line Lean mixture causing misfire
   High	High	Rough idle (Black smoke from exhaust)	Restricted air cleaner filter element Plugged PCV valve Faulty SFI system: Faulty pressure regulator Defective engine coolant temperature sensor Defective mass air flow meter Faulty ECM Faulty injectors Faulty throttle position sensor

Check the throttle control motor operating sound.

1. Turn the ignition switch to ON.
   

2. When depressing the accelerator pedal, check the operating sound of the running motor. Make sure that no friction noises are emitted from the motor. If friction noise exists, replace the throttle body.
   

Check the throttle position sensor.

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON.
   

3. Turn the intelligent tester on.
   

4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Sensor Position.
   

   Standard throttle valve opening percentage:

   60% or more
   

   NOTICE:

   When checking the standard throttle valve opening percentage, make sure the transmission is in neutral.

   If the result is not as specified, check the throttle body with motor, the wire harness and the ECM.