Oil And Oil Filter Replacement

Engine Hybrid System. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
2Tr-Fbe Lubrication. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

  1. REMOVE NO. 2 ENGINE UNDER COVER

  2. DRAIN ENGINE OIL

  3. REMOVE OIL FILTER SUB-ASSEMBLY

  4. INSTALL OIL FILTER SUB-ASSEMBLY

  5. ADD ENGINE OIL

  6. INSPECT FOR OIL LEAK

  7. INSPECT ENGINE OIL LEVEL

  8. INSTALL NO. 2 ENGINE UNDER COVER

Oil And Oil Filter -- Replacement


CAUTION:
  1. Prolonged and repeated contact with mineral oil will result in the loss of natural oil from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash the area thoroughly with soap and waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.
  3. In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.


1. REMOVE NO. 2 ENGINE UNDER COVER


2. DRAIN ENGINE OIL

  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the oil into a container.

  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    38 N*m{382 kgf*cm, 28 ft.*lbf}


3. REMOVE OIL FILTER SUB-ASSEMBLY


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Tr-Fbe Lubrication.Lubrication System.Oil And Oil Filter Replacement

  1. Using SST, remove the oil filter.

    SST
    09228-07501


4. INSTALL OIL FILTER SUB-ASSEMBLY

  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.



    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.2Tr-Fbe Lubrication.Lubrication System.Oil And Oil Filter Replacement

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.

  1. Using SST, tighten the oil filter.

    SST
    09228-07501

    1. Depending on the work space available, choose from the following.
      If enough space is available, use a torque wrench to tighten the oil filter.

      Torque:
      17 N*m{175 kgf*cm, 13 ft.*lbf}
      If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or use a common wrench.


5. ADD ENGINE OIL

  1. Add fresh engine oil.

    Standard Oil Grade:
    Oil Grade
    		Oil Viscosity (SAE)
    API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
    		5W-30
    10W-30
    (5W-30 is the best choice for good fuel economy and good starting in cold weather)
    API grade SL, SM or SN multigrade engine oil
    		15W-40
    20W-50
    Standard Capacity:
    Item
    		Capacity
    Drain and refill without oil filter change
    		5.3 liters (5.6 US qts, 4.7 Imp. qts)
    Drain and refill with oil filter change
    		5.6 liters (5.9 US qts, 4.9 Imp. qts)
    Dry fill
    		6.3 liters (6.7 US qts, 5.5 Imp. qts)

  1. Install the oil filler cap.



6. INSPECT FOR OIL LEAK

  1. Start the engine, and check that there are no oil leaks after performing maintenance.



7. INSPECT ENGINE OIL LEVEL

  1. Warm up the engine, and then stop the engine and wait for 5 minutes.
    If the oil level is low, check for leakage and add oil up to the full level mark.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.


8. INSTALL NO. 2 ENGINE UNDER COVER
Torque:
28 N*m{286 kgf*cm, 21 ft.*lbf}