Vehicle Stability Control System Tc And Cg Terminal Circuit

Brake. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25
Brake Control Dynamic Control Systems. Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK CAN COMMUNICATION SYSTEM

INSPECT DLC3

CHECK ECM (DLC3 INPUT)

CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

CHECK ECM (DLC3 INPUT)

VEHICLE STABILITY CONTROL SYSTEM - TC and CG Terminal Circuit


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to output the DTCs by blinking the ABS warning light and VSC OFF indicator light.

WIRING DIAGRAM


Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Brake Control Dynamic Control Systems.Anti-Lock Brake System.Vehicle Stability Control System Tc And Cg Terminal Circuit

HINT:
When the warning light and indicator light continue to blink, there may be a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs.

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (HILUX_TGN26 RM000000XHR073X.html).
  2. Before disconnecting the connector, make sure that there are no problems with the connection.
  3. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
1.CHECK CAN COMMUNICATION SYSTEM

  1. Check if a CAN communication system DTC is output (HILUX_TGN26 RM000004PEV00AX.html).

    Result
    Result
    		Proceed to
    DTC is not output
    		A
    DTC is output
    		B


B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (HILUX_TGN26 RM000004PEM00AX.html)
A


2.INSPECT DLC3


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Brake Control Dynamic Control Systems.Anti-Lock Brake System.Vehicle Stability Control System Tc And Cg Terminal Circuit

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    G18-13 (TC) - G18-4 (CG)
    		Ignition switch ON
    		11 to 14 V
    Text in Illustration
    *a
    		Front view of DLC3


NG
Go to step 4
OK


3.CHECK ECM (DLC3 INPUT)
SST
09843-18040


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Brake Control Dynamic Control Systems.Anti-Lock Brake System.Vehicle Stability Control System Tc And Cg Terminal Circuit

  1. Turn the ignition switch off.

  1. Connect the G39 ECM connector.

  1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

    Text in Illustration
    *a
    		Front view of DLC3

  1. Turn the ignition switch to ON.

  1. Check that the MIL is blinking.

    Result
    Result
    		Proceed to
    MIL is blinking
    		A
    MIL is not blinking
    		B
    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (HILUX_TGN26 RM000000XHN0F2X.html).


B
REPAIR OR REPLACE WIRE HARNESS OR ECM
A

REPLACE BRAKE ACTUATOR ASSEMBLY (HILUX_TGN26 RM0000010K001MX.html)

4.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

  1. Turn the ignition switch off.

  1. Disconnect the G39 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    G18-13 (TC) - G39-11 (TC)
    		Always
    		Below 1 Ω
    G18-13 (TC) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    G18-4 (CG) - Body ground
    		Always
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK ECM (DLC3 INPUT)
SST
09843-18040


    Hilux. Tgn26, 36 Kun25, 26, 35, 36 Ggn25.Brake Control Dynamic Control Systems.Anti-Lock Brake System.Vehicle Stability Control System Tc And Cg Terminal Circuit

  1. Turn the ignition switch off.

  1. Connect the G39 ECM connector.

  1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

    Text in Illustration
    *a
    		Front view of DLC3

  1. Turn the ignition switch to ON.

  1. Check that the MIL is blinking.

    Result
    Result
    		Proceed to
    MIL is blinking
    		A
    MIL is not blinking
    		B


B
REPAIR OR REPLACE WIRE HARNESS OR ECM
A

REPLACE BRAKE ACTUATOR ASSEMBLY (HILUX_TGN26 RM0000010K001MX.html)