Ecd System (For Dpf) Engine Difficult To Start Or Stalling

DESCRIPTION

INSPECTION PROCEDURE

CHECK ENGINE CRANKING CONDITION

READ ALL OUTPUT DTCS

TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)

CHECK SNAPSHOT (FUEL PRESS)

CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP

CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

BLEED AIR FROM FUEL SYSTEM

PERFORM FUEL SUPPLY PUMP INITIALIZATION

READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)

CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)

BLEED AIR FROM FUEL SYSTEM

READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

PERFORM FUEL SUPPLY PUMP INITIALIZATION

REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

INSPECT INJECTOR ASSEMBLY (CHECKING FOR PRESENCE OF AIR)

CHECK DATA LIST

REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)

CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER

BLEED AIR FROM FUEL SYSTEM

REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

INSPECT INJECTOR DRIVER

INSPECT INJECTOR ASSEMBLY (CHECKING FOR PRESENCE OF AIR)

CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS

READ VALUE USING ENGINE COOLANT TEMPERATURE SENSOR (COOLANT TEMP)

INSPECT GLOW PLUG (RESISTANCE)

CHECK FUEL QUALITY

READ OUTPUT DTC (RELATED TO ENGINE)

CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM

READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

CHECK STARTING SYSTEM

CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

ECD SYSTEM (for DPF) - Engine Difficult to Start or Stalling

DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components

1. Engine Control
   
   

   Mass Air Flow Meter

   Main fault		Decrease in performance (foreign matter is stuck)
   Symptoms		Lack of power, black smoke
   Data List		MAF
   HINT: The maximum fuel injection volume is controlled according to the output from the mass air flow meter.

   
   

   Intake System

   Symptom and Corresponding Main Fault		Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct Black smoke (no lack of power) due to leakage between the turbo and intake manifold
   Data List		MAP

   
   

   Turbocharger System

   Main fault		Air leak in the turbocharged air passage ECM not operating well Turbocharger (turbine, bearing)
   Symptoms		Lack of power (when vehicle is starting, under heavy load) (Black smoke is not emitted when racing while vehicle is stopped)
   Data List		MAP With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure. Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions.

   
   

   Exhaust System

   Main fault		Blockage
   Symptoms		Lack of power (high engine speed, under heavy load)

   
   

   Glow System

   Main fault		Glow system malfunction
   Symptoms		Difficult to start, rough idle, knocking, white smoke (when cold)
   Data List		Check the glow plug indicator light
   Diagnostic Point		Measure the resistance of the glow plug

   
   

   Battery

   Main fault		Battery is depleted
   Symptoms		Difficult to start (cannot crank, crank speed is low), horn is quiet
   Data List		Battery Voltage When cranking, battery voltage is below 5 V.

   
   

   Engine - 1

   Main fault		Damaged, seized up
   Symptoms		Cannot crank, crank speed is low, strange noise

   
   

   Engine - 2

   Main fault		Loss of compression
   Symptoms		Rough idle (lack of power always)
   Data List		Engine Speed of Cyl When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression. Injection Feedback Val When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.

   
   

   Start System

   Main fault		Starter system malfunction
   Symptoms		Difficult to start
   Data List		Starter Signal Ignition switch (STA) output: ON: Starter is operating OFF: Starter is not operating

2. Diesel Injection
   
   

   Fuel Supply Pump

   Main fault		-
   Symptoms		Difficult to start, engine stalling, rough idle, lack of power
   Data List		Fuel Press, Target Common Rail Pressure, Target Pump SCV Current Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)). If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt. If the fuel pressure is below 25000 kPa, then idling will be rough. HINT: The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up. When Target Pump SCV Current is 3000 mA or higher, the suction control valve has a tendency to become stuck.
   Diagnostic Trouble Code		Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

   
   

   Fuel Filter

   Main fault		Blockage
   Symptoms		Difficult to start, engine stalling, rough idle, lack of power
   Data List		Fuel Press, Target Common Rail Pressure Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)). If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt. If the fuel pressure is below 25000 kPa, then idling will be rough. HINT: The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.
   Diagnostic Trouble Code		Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

   
   

   Injector Assembly

   Main fault		Blockage
   Symptoms		Rough idle, lack of power, black smoke, white smoke, knocking
   Data List		Injection Feedback Val When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.

   
   

   Pressure Discharge Valve

   Main fault		Does not completely close
   Symptoms		Difficult to start, engine stall, rough idle, lack of power

   
   

   Injector Driver

   Main fault		Circuit fault: The injector assembly does not open.
   Symptoms		Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
   Data List		Same as injector assembly
   Diagnostic Trouble Code		When the injector driver has a fault, some DTCs may be stored.

   
   

   Fuel Pressure Sensor

   Main fault		Open circuit, decrease in performance (foreign matter is stuck)
   Symptoms		Difficult to start, rough idle, engine stall, lack of power
   Data List		Fuel Press, Target Common Rail Pressure Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Press and Common Rail Pres Sens 2 follow Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Fuel Press or Common Rail Pres Sens 2 decreases to a value less than Target Common Rail Pressure).
   Diagnostic Trouble Code		When the fuel pressure sensor has a fault, some DTCs may be stored.

   
   

   Irregular Fuel

   Main fault		-
   Symptoms		Difficult to start, rough idle (especially when cold)

3. Diesel EGR
   
   

   EGR System

   Main fault		Does not move smoothly Does not close completely
   Symptoms		Rough idle EGR valve stuck closed: A loud turbocharger sound. EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).
   Data List		Actual EGR Valve Pos., Target EGR Position Generally, Actual EGR Valve Pos. = Target EGR Position +/-5% (fully closed: 0%, fully open: 100%). Using the EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Position (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs). EGR valve is fully closed when the ignition switch is turned to ON (engine stopped). EGR valve opens to the halfway point at idling after the engine is warmed up. EGR Close Lrn. Val., EGR Close Lrn. Status When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0 to 1 V. In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.

4. Diesel Throttle
   
   

   Diesel Throttle System

   Main fault		Stuck, does not move smoothly
   Symptoms		Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed. Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
   Data List		Actual Throttle Position 0%: Fully open 100%: Fully closed When the ignition switch ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.

Data List Related to Starting Trouble

1. MAP
   
2. MAF
   
3. Intake Air
   
4. Coolant Temp
   
5. Battery Voltage
   
6. Starter Signal
   
7. Engine Speed of Cyl #1 (to #4)
   
8. Target Common Rail Pressure
   
9. Fuel Press
   
10. Target Pump SCV Current
    
11. Injection Feedback Val #1 (to #4)
    
12. Injection Volume
    
13. Actual Throttle Position
    
14. Target EGR Position
    
15. Actual EGR Valve Pos.
    
16. EGR Close Lrn. Status
    
17. EGR Close Lrn. Val.
    

INSPECTION PROCEDURE

Explanation of Symptom

Starting Trouble

For good starting it is essential to have: Sufficient cranking speed. Properly operating engine preheating system. Good quality fuel. The fuel is ignited by the heat which is generated by compression pressure. With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is poor due to leakage, the compression pressure will not rise and there will be difficulty starting. When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plugs heat the compressed air. Also, after starting the engine, by charging the glow plugs for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the injector assembly is open.

Trouble Area Chart According to Problem Cause

NOTICE:

1. After replacing the ECM, the new ECM needs registration (HILUX_TGN26 RM0000012XK07EX.html) and initialization (HILUX_TGN26 RM000000TIN056X.html).
   
2. After replacing the Fuel Supply Pump, the ECM needs initialization (HILUX_TGN26 RM000000TIN056X.html).
   
3. After replacing an injector assembly, the ECM needs registration (HILUX_TGN26 RM0000012XK07EX.html).
   

HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.

1.CHECK ENGINE CRANKING CONDITION

1. Check the engine cranking condition.
   
   

   Result

   Result	Proceed to
   Cranking is OK.	A
   Low cranking speed. HINT: When cranking speed is low, especially when the temperature is low, check if the engine oil grade matches the recommendation.	B
   Does not crank at all.	C

B	CHECK BATTERY CONDITION (HILUX_TGN26 RM0000013Y001JX_01_0001.html)
C	Go to step 34

A

2.READ ALL OUTPUT DTCS

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Enter the following menus: Utility / All Codes.
   
   

   Result

   Result	Proceed to
   No DTC is output	A
   Engine related DTCs are output	B

   HINT:

   If only DTC P1604 is output, proceed to step 3.

B	GO TO RELATED DTC (HILUX_TGN26 RM0000031HW04RX.html)

A

3.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
   

4. Take a snapshot when idling with no load after the engine is warmed up and when starting trouble is occurring.
   

   Text in Illustration

   *1	Snapshot Button

   HINT:

   1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the illustration below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
      
   2. When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.
      
   3. Graphs like the ones shown below can be displayed by transferring the stored snapshot from the tester to a PC. Intelligent Viewer must be installed on the PC.
      
   4. Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up and when the engine is started.
      

NEXT

4.CHECK SNAPSHOT (FUEL PRESS)

1. Check Fuel Press in the snapshot taken in procedure 3 when the engine was started.
   

   
   
   
   
   

   Result

   Result	Proceed to
   At the point in the illustration labeled "a", Fuel Press is less than 10000 kPa from the value of Fuel Press when cranking started	A
   At the point in the illustration labeled "c", Fuel Press is below Target Common Rail Pressure by 15000 kPa or more	B
   Fuel Press increases to a value that is higher than Target Common Rail Pressure immediately after cranking, and, at the point in the illustration labeled "d", Fuel Press is higher than Target Common Rail Pressure	C
   Except above	D

   HINT:

   1. Even if Fuel Press is temporarily higher than Target Common Rail Pressure, as shown at the point in the illustration labeled "b", the fuel supply pump is normal.
      
   2. Fuel pressure is about 25000 to 35000 kPa when the engine is cranking and the engine coolant temperature is 0°C (32°F) or higher.
      
   3. Fuel pressure increases rapidly during cranking.
      

B	Go to step 14
C	Go to step 28
D	Go to step 18

A

5.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP

1. Disconnect the inlet hose from the Fuel Supply Pump.
   

2. Operate the priming pump and check that fuel is being supplied to the Fuel Supply Pump.
   

   OK:

   Fuel is properly supplied to the fuel supply pump when the priming pump is operated.
   

   HINT:

   1. When there is a lack of fuel, fuel pressure drops.
      
   2. Inspect for Fuel Filter clogging (check that the Fuel Filter is not clogged).
      

3. Reconnect the inlet hose.
   

NG	Go to step 12

OK

6.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

1. Disconnect the suction control valve connector.
   

2. Disconnect the ECM connector.
   

3. Measure the resistance according to the value(s) in the table below.
   
   

   Standard Resistance:

   
   

   Tester Connection	Condition	Specified Condition
   C5-1 - C111-23 (PCV+)	Always	Below 1 Ω
   C5-2 - C111-12 (PCV-)	Always	Below 1 Ω
   C5-1 or C111-23 (PCV+) - Body ground	Always	10 kΩ or higher
   C5-2 or C111-12 (PCV-) - Body ground	Always	10 kΩ or higher

4. Reconnect the suction control valve connector.
   

5. Reconnect the ECM connector.
   

NG	REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

1. Replace the fuel supply pump assembly (HILUX_TGN26 RM0000014FO028X.html).
   

NEXT

8.BLEED AIR FROM FUEL SYSTEM

1. Bleed the air from the fuel system (HILUX_TGN26 RM000002SY802GX_01_0002.html).
   

NEXT

9.PERFORM FUEL SUPPLY PUMP INITIALIZATION

1. Perform fuel supply pump initialization (HILUX_TGN26 RM000000TIN056X.html).
   

NEXT

10.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
   

4. Start the engine.
   

5. Read the Fuel Press values while cranking and idling the engine.
   
   

   Result

   Result	Proceed to
   The engine cannot be started or the engine can be started but Fuel Press is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON	B
   Except above	A

B	Go to step 11

A
END

11.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)

1. Remove the glow plug assembly for all the cylinders (HILUX_TGN26 RM000000JIT00TX.html).
   

2. Visually check if there is fuel on the glow plugs.
   

   HINT:

   1. If there is fuel on a glow plug, fuel may be leaking from an injector assembly.
      
   2. After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPa of the target fuel pressure while cranking the engine.
      
   3. If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.
      

3. Install the glow plug assembly (HILUX_TGN26 RM000000JIQ00UX.html).
   

NEXT	Go to step 23

12.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)

1. Check and repair or replace the clogged fuel pipe.
   

NEXT

13.BLEED AIR FROM FUEL SYSTEM

1. Bleed the air from the fuel system (HILUX_TGN26 RM000002SY802GX_01_0002.html).
   

NEXT	Go to step 27

14.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

1. Check Fuel Press in the snapshot taken in procedure 3 when the engine was warmed up.
   
   

   Result

   Result	Proceed to
   Difference between Fuel Press and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or more	A
   Except above	B

B	Go to step 17

A

15.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

1. Replace the fuel supply pump assembly (HILUX_TGN26 RM0000014FO028X.html).
   

NEXT

16.PERFORM FUEL SUPPLY PUMP INITIALIZATION

1. Perform fuel supply pump initialization (HILUX_TGN26 RM000000TIN056X.html).
   

NEXT

17.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

1. Replace the injector assemblies (HILUX_TGN26 RM0000044TN00PX.html).
   

   NOTICE:

   1. When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
      
   2. Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
      
   3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
      
   4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
      
   5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
      

NEXT	Go to step 24

18.INSPECT INJECTOR ASSEMBLY (CHECKING FOR PRESENCE OF AIR)

1. When the engine does not start, perform the following procedure.
   

   1. Stop the engine and leave the vehicle for 4 hours or more.
      

      HINT:

      It is necessary to leave the vehicle for 4 hours or more to wait for air in the injector assembly to come out.

   2. Check that the engine starts.
      

      OK:

      The engine starts.
      

2. When the engine starts, perform the following procedure.
   

   1. Bleed the air from the fuel system (HILUX_TGN26 RM000002SY802GX_01_0002.html).
      

   2. Check that the engine starts.
      

      OK:

      The engine starts.
      

NG	Go to step 19

OK
END

19.CHECK DATA LIST

1. Check Injection Feedback Val # in the snapshot taken in procedure 3 when the engine was idling.
   

   Text in Illustration

   *1	Snapshot Button

   
   

   Result

   Result	Proceed to
   Injection Feedback Val #1 to #4 are 3 mm3/st or less. Injection Volume is more than 12 mm3/st.	A*
   Injection Feedback Val for at least one cylinder is more than +3 mm3/st HINT: There may be a malfunction in the corresponding cylinder.	B
   Except above	C

   HINT:

   1. *: When this case occurs, usually symptoms may be noticeable, such as difficulty starting, lack of power.
      
   2. The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
      

B	Go to step 21
C	Go to step 30

A

20.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

1. Replace the injector assemblies (HILUX_TGN26 RM0000044TN00PX.html).
   

   NOTICE:

   1. When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
      
   2. Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
      
   3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
      
   4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
      
   5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
      

NEXT	Go to step 24

21.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)

HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.

1. Connect the intelligent tester to the DLC3.
   

2. Start the engine and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
   

4. Check the engine speed during the Active Test.
   
   

   Result

   Result	Proceed to
   Except below	A
   The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other.	B

   HINT:

   When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.

B	Go to step 23

A

22.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

HINT:

Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.

1. Check the cylinder compression pressure (HILUX_TGN26 RM000001473021X_01_0002.html).
   

NG	CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

OK

23.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

HINT:

It can be determined that the injector assembly is faulty as the corresponding cylinder is malfunctioning, but has no compression loss.

1. Replace the injector assembly (HILUX_TGN26 RM0000044TN00PX.html).
   

   NOTICE:

   1. When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
      
   2. Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
      
   3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
      
   4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
      
   5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
      

NEXT

24.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER

1. Clean the fuel filter case and replace the fuel filter.
   

   HINT:

   Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.

NEXT

25.BLEED AIR FROM FUEL SYSTEM

1. Bleed the air from the fuel system (HILUX_TGN26 RM000002SY802GX_01_0002.html).
   

NEXT

26.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

1. Register the injector compensation codes (HILUX_TGN26 RM0000012XK07EX_02_0003.html).
   

2. Perform the injector pilot quantity learning (HILUX_TGN26 RM0000012XK07EX_02_0009.html).
   

NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT
END

28.INSPECT INJECTOR DRIVER

1. Even in cases where DTC P062D is not stored even though the engine cannot be started, perform the DTC P062D (No. 1 Fuel Injector Driver Circuit Performance) troubleshooting procedure (HILUX_TGN26 RM00000187V060X.html).
   When troubleshooting the injector driver (EDU) circuit, the source of the malfunction is likely to be in one of the following areas, so be sure to inspect these areas carefully.
   

   1. Injector driver (EDU) system power source circuit
      
   2. Injector assembly circuit
      
   3. Injector driver (EDU)
      
   4. ECM
      

   HINT:

   1. When the engine cannot be started due to a malfunction in the injector driver (EDU) circuit, once the DTCs are cleared, the system cannot store DTC P062D even if it is confirmed that the engine cannot be started when trying to reproduce the problem symptoms.
      As DTC P062D cannot be stored when starting the engine, fuel injection signals are output by the ECM, but fuel is not actually injected. Therefore, an excessive amount of fuel is supplied to the common rail by the fuel supply pump assembly, and as a result, the fuel pressure is higher than the target common rail pressure in the data recorded at the time the engine was having trouble starting.
      
   2. If the problem cannot be determined even after performing the DTC P062D (No. 1 Fuel Injector Driver Circuit Performance) troubleshooting procedure and the fuel pressure is higher than the target common rail pressure when attempting to start the engine, proceed to the next step.
      
   3. Perform the troubleshooting procedure for DTC P062D and proceed to the diagnostic flow situations where the engine does not start.
      

   Result

   Result	Proceed to
   Injector driver (EDU) circuit is normal	A
   Injector driver (EDU) circuit is abnormal	B

B	REPAIR OR REPLACE MALFUNCTIONING PARTS

A

29.INSPECT INJECTOR ASSEMBLY (CHECKING FOR PRESENCE OF AIR)

1. When the engine does not start, perform the following procedure.
   

   1. Stop the engine and leave the vehicle for 4 hours or more.
      

      HINT:

      It is necessary to leave the vehicle for 4 hours or more to wait for air in the injector assembly to come out.

   2. Confirm the engine starts.
      

2. When the engine starts, perform the following procedure.
   

   1. Bleed the air from the fuel system (HILUX_TGN26 RM000002SY802GX_01_0002.html).
      

   2. Confirm the engine starts.
      

NEXT	Go to step 38

30.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS

1. Check the temperature when starting trouble occurs.
   

Result

Result	Proceed to
Difficult to start only for cold engine.	A
Difficult to start both for cold and warmed up engine.	B

B	Go to step 33

A

31.READ VALUE USING ENGINE COOLANT TEMPERATURE SENSOR (COOLANT TEMP)

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
   

4. Read the value displayed on the tester.
   

   OK:

   Coolant Temp is not high when the engine is cold, and not low after the engine is warmed up
   

NG	INSPECT ENGINE COOLANT TEMPERATURE SENSOR (HILUX_TGN26 RM0000013Z8017X.html)

OK

32.INSPECT GLOW PLUG (RESISTANCE)

1. Inspect the glow plug (HILUX_TGN26 RM0000044ZK009X_01_0001.html).
   

NG	REPLACE GLOW PLUG (HILUX_TGN26 RM000000JIT00TX.html)

OK

33.CHECK FUEL QUALITY

1. Check that only diesel fuel is being used.
   

2. Check that the fuel does not contain any impurities.
   

NEXT	Go to step 38

34.READ OUTPUT DTC (RELATED TO ENGINE)

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / DTC.
   

4. Read the DTCs.
   
   

   Result

   Result	Proceed to
   No DTC is output	A
   Engine related DTCs are output	B

B	GO TO RELATED DTC (HILUX_TGN26 RM0000031HW04RX.html)

A

35.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Check if the normal starting screen appears (check whether communication with the ECM is possible).
   

   HINT:

   Use a tester that is able to communicate with other vehicles.

   OK:

   Communication is possible (vehicle can be recognized).
   

NG	CHECK VC OUTPUT CIRCUIT (HILUX_TGN26 RM000001D6V0OPX.html)

OK

36.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

1. Connect the intelligent tester to the DLC3.
   

2. Turn the ignition switch to ON and turn the tester on.
   

3. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
   

4. Read the value displayed on the tester.
   
   

   OK:

   
   

   Tester Display	Condition	Specified Condition
   Starter Signal	Cranking	ON

NG	INSPECT CLUTCH SWITCH ASSEMBLY

OK

37.CHECK STARTING SYSTEM

1. Inspect the starting system.
   

   HINT:

   Be sure to inspect the following areas:

   1. Starter relay
      
   2. Starter
      
   3. Immobiliser system
      

NEXT

38.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT
END