Dtc P060A Internal Control Module Monitoring Processor Performance

Engine Hybrid System. Corolla. Zre142 Aze141
2Az-Fe Engine Control. Corolla. Zre142 Aze141

MONITOR DESCRIPTION

MONITOR STRATEGY

TYPICAL ENABLING CONDITIONS

TYPICAL MALFUNCTION THRESHOLDS

CONFIRMATION DRIVING PATTERN

INSPECTION PROCEDURE

READ OUTPUT DTC (DTC P060A)

DTC P060A Internal Control Module Monitoring Processor Performance


MONITOR DESCRIPTION

The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU monitors the communications and WDC pulses from the sub CPU. When the signal malfunctions below are detected, the DTC is stored.

DTC No.
DTC Detection Condition
Trouble Area
P060A
A CPU reset is performed after one of the following conditions is met (1 trip detection logic):
  1. There is an ECM main CPU error.
  2. There is an ECM sub CPU error.
  3. There is an electronic throttle monitoring CPU error.
ECM

MONITOR STRATEGY


Related DTCs
P060A: ECM CPU error
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
-
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None

TYPICAL MALFUNCTION THRESHOLDS


Either of the following conditions is met:
Condition 1 or 2
1. All of the following conditions are met:
-
- CPU reset
1 time or more
- Learned throttle position - Learned accelerator pedal position
0.4 V or more
- Electronic throttle actuator
Off
2. CPU reset
2 times or more

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the Techstream off.
  5. Turn the ignition switch off.
  6. Disconnect the Techstream.
  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  8. Connect the cable to the negative (-) battery terminal.
  9. Connect the Techstream to the DLC3.
  10. Turn the ignition switch to ON and turn the Techstream on.
  11. Wait 16 seconds or more.
  12. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  13. Read the pending DTCs.
    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.
  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P060A.
  16. Check the DTC judgment result.

    Techstream Display
    		Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
  17. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (COROLLA_ZRE142 RM000000PDK0ZBX.html).
    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.READ OUTPUT DTC (DTC P060A)

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (COROLLA_ZRE142 RM000000PDK0ZBX.html).

  1. Turn the ignition switch off and turn the Techstream off.

  1. Disconnect the Techstream.

  1. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Wait 16 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result
    Result
    		Proceed to
    DTC is not output
    		A
    DTC P060A is output
    		B



B
REPLACE ECM (COROLLA_ZRE142 RM000002WT402ZX.html)
A

CHECK FOR INTERMITTENT PROBLEMS (COROLLA_ZRE142 RM000000PDQ0VNX.html)