Smart Key System (For Entry Function) Driver Side Door Entry Lock Function Does Not Operate

Vehicle Interior. Corolla. Zre142 Aze141
Theft Deterrent Keyless Entry. Corolla. Zre142 Aze141

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

CHECK POWER DOOR LOCK OPERATION

READ VALUE USING TECHSTREAM (DOOR LOCK POSITION SWITCH)

READ VALUE USING TECHSTREAM (OUTSIDE HANDLE)

CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)

CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)

INSPECT FRONT DOOR OUTSIDE HANDLE (for Driver Side)

REPLACE DOOR ELECTRICAL KEY OSCILLATOR

CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)

SMART KEY SYSTEM (for Entry Function) - Driver Side Door Entry Lock Function does not Operate


DESCRIPTION

If the driver door entry lock function does not operate but the entry unlock function operates, communication between the vehicle and electrical key transmitter is normal. As a result, the entry lock switch circuit can be considered to be faulty (certification ECU (smart key ECU assembly) → driver side outside handle (entry lock switch) → driver side door electrical key oscillator).

WIRING DIAGRAM


Corolla. Zre142 Aze141.Theft Deterrent Keyless Entry.Smart Key System (For Entry Function).Smart Key System (For Entry Function) Driver Side Door Entry Lock Function Does Not Operate


INSPECTION PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION

  1. When the master switch assembly's door control switch is operated, check that the doors lock (COROLLA_ZRE142 RM000001333049X.html).

    OK:
    Door locks operate normally.


NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (COROLLA_ZRE142 RM000000TNU06AX.html)
OK


2.READ VALUE USING TECHSTREAM (DOOR LOCK POSITION SWITCH)

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body (Main Body ECU (Instrument Panel Junction Block))
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    D-Door Lock Pos SW
    		Driver side door lock position switch signal/ON or OFF
    		ON: Driver side door is unlocked
    OFF: Driver side door is locked
    		-
    OK:
    On the Techstream screen, the display changes between ON and OFF as shown in the chart above.

    Result:

    Result
    		Proceed to
    OK
    		A
    NG
    		B
    (Refer to "Driver Door LOCK/UNLOCK Functions do not Operate" in the problem symptoms table)


B
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table) (Link)
A


3.READ VALUE USING TECHSTREAM (OUTSIDE HANDLE)

  1. Enter the following menus: Body Electrical / Smart Key / Data List.

  1. Read the Data List according to the display on the Techstream.

    Smart Key (Certification ECU (Smart Key ECU Assembly))
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    D-Door Trigger SW
    		Driver side door lock switch/ON or OFF
    		ON: Switch is touched
    OFF: Switch is not touched
    		-
    OK:
    On the Techstream screen, the item changes between ON and OFF according to the chart above.


NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (COROLLA_ZRE142 RM000003G0O004X.html)

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)

  1. Disconnect the front door outside handle.



    Corolla. Zre142 Aze141.Theft Deterrent Keyless Entry.Smart Key System (For Entry Function).Smart Key System (For Entry Function) Driver Side Door Entry Lock Function Does Not Operate

  1. Disconnect the door electrical key oscillator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    T2-9 (TRG-) - T1-1 (TRG-)
    		Always
    		Below 1 Ω
    T2-9 (TRG-) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)


    Corolla. Zre142 Aze141.Theft Deterrent Keyless Entry.Smart Key System (For Entry Function).Smart Key System (For Entry Function) Driver Side Door Entry Lock Function Does Not Operate

  1. Disconnect the certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    E36-3 (TSW1) - T1-3 (TRG+)
    		Always
    		Below 1 Ω
    E36-3 (TSW1) - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT FRONT DOOR OUTSIDE HANDLE (for Driver Side)


    Corolla. Zre142 Aze141.Theft Deterrent Keyless Entry.Smart Key System (For Entry Function).Smart Key System (For Entry Function) Driver Side Door Entry Lock Function Does Not Operate

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    T1-1 (TRG-) - T1-3 (TRG+)
    		Lock switch not pushed
    		10 kΩ or higher
    T1-1 (TRG-) - T1-3 (TRG+)
    		Lock switch pushed
    		Below 1 Ω


NG
REPLACE FRONT DOOR OUTSIDE HANDLE (COROLLA_ZRE142 RM000002Y8000YX.html)
OK


7.REPLACE DOOR ELECTRICAL KEY OSCILLATOR

  1. Replace the door electrical key oscillator (COROLLA_ZRE142 RM0000011QF0BCX.html).


NEXT


8.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)

  1. Check that the entry functions operate normally.

    OK:
    Entry functions operate normally.


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (COROLLA_ZRE142 RM000003G0O004X.html)
OK

END (DOOR ELECTRICAL OSCILLATOR IS DEFECTIVE)