Theft Deterrent System (W/O Entry And Start System) Ignition Switch Circuit

Securities. Camry. Acv40 Gsv40
Theft Deterrent. Camry. Acv40 Gsv40

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

READ VALUE USING INTELLIGENT TESTER

CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL J/B)

INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B - INSTRUMENT PANEL J/B)

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B - BODY GROUND)

THEFT DETERRENT SYSTEM (w/o Entry and Start System) - Ignition Switch Circuit


DESCRIPTION

The main body ECU determines the ignition position (OFF, ACC, ON) based on signals from the IG or ACC circuit.

WIRING DIAGRAM


Camry. Acv40 Gsv40.Theft Deterrent.Theft Deterrent System (W/ Entry And Start System).Theft Deterrent System (W/O Entry And Start System) Ignition Switch Circuit


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER

  1. Connect the intelligent tester (with CAN VIM) to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the intelligent tester main switch on.

  1. Select the item below in the Data List and read the display on the intelligent tester.

    MAIN BODY (Main Body ECU):
    Item
    		Test Details
    		Diagnostic Note
    IG SW
    		ignition switch ON signal ON/OFF
    		-
    ACC SW
    		ignition switch ACC signal ON/OFF
    		-
    OK:
    When the ignition switch is operated, the display changes as shown in the table.


NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL J/B)


    Camry. Acv40 Gsv40.Theft Deterrent.Theft Deterrent System (W/ Entry And Start System).Theft Deterrent System (W/O Entry And Start System) Ignition Switch Circuit

  1. Disconnect the IA J/B connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    		Condition
    		Specified Condition
    IA-1 - Body ground
    		Ignition switch ON
    		10 to 14 V


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY


    Camry. Acv40 Gsv40.Theft Deterrent.Theft Deterrent System (W/ Entry And Start System).Theft Deterrent System (W/O Entry And Start System) Ignition Switch Circuit

  1. Disconnect the E23 switch connector from the ignition switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    1 - 4
    		Ignition switch ON
    		Below 1 Ω
    2 - 4
    		Ignition switch ACC
    		Below 1 Ω


NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B - INSTRUMENT PANEL J/B)


    Camry. Acv40 Gsv40.Theft Deterrent.Theft Deterrent System (W/ Entry And Start System).Theft Deterrent System (W/O Entry And Start System) Ignition Switch Circuit

  1. Disconnect the II J/B connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    II-4 - II-9
    		Ignition switch ON
    		Below 1 Ω
    II-4 - II-3
    		Ignition switch ACC
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B - BODY GROUND)


    Camry. Acv40 Gsv40.Theft Deterrent.Theft Deterrent System (W/ Entry And Start System).Theft Deterrent System (W/O Entry And Start System) Ignition Switch Circuit

  1. Disconnect the IF J/B connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Specified Condition
    IF-10 - Body ground
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY