Lighting System Interior Light Circuit

Body Electrical. Camry. Acv40 Gsv40
Lighting. Camry. Acv40 Gsv40

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

PERFORM ACTIVE TEST USING INTELLIGENT TESTER

CHECK VEHICLE CONDITION

CHECK HARNESS AND CONNECTOR (LIGHT - BATTERY AND INSTRUMENT PANEL J/B ASSEMBLY)

CHECK HARNESS AND CONNECTOR (LIGHT - BATTERY AND INSTRUMENT PANEL J/B ASSEMBLY)

LIGHTING SYSTEM - Interior Light Circuit


DESCRIPTION

The main body ECU controls the illuminated entry system (interior light and ignition key cylinder light).

WIRING DIAGRAM


Camry. Acv40 Gsv40.Lighting.Lighting System.Lighting System Interior Light Circuit


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Select the item(s) below in the ACTIVE TEST, and check the operation.

    Main Body (Main Body ECU):
    Item
    		Test Details
    		Diagnostic Note
    INTERIOR LAMP
    		Interior light and ignition key cylinder light ON / OFF (Interior light switch is in DOOR position and all doors are closed).
    		-
OK:
Each light illuminates.


OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.CHECK VEHICLE CONDITION

  1. Check the vehicle condition.

    Result:

    Condition
    		Proceed to
    without Sliding Roof
    		A
    with Sliding Roof
    		B


B
Go to step 4
A


3.CHECK HARNESS AND CONNECTOR (LIGHT - BATTERY AND INSTRUMENT PANEL J/B ASSEMBLY)


    Camry. Acv40 Gsv40.Lighting.Lighting System.Lighting System Interior Light Circuit

  1. Disconnect the E25 transponder key amplifier connector.

  1. Disconnect the Q9 rear room light assembly connector.

  1. Disconnect the IR and II instrument panel J/B assembly connectors.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    		Condition
    		Specified Condition
    E25-2 - Body ground
    		Always
    		10 to 14 V
    Q9-1 - Body ground
    		Always
    		10 to 14 V
    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    II-10 - E25-6
    		Always
    		Below 1 Ω
    IR-5 - Q9-2
    		Always
    		Below 1 Ω
    II-10 - Body ground
    		Always
    		10 kΩ or higher
    IR-5 - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (LIGHT - BATTERY AND INSTRUMENT PANEL J/B ASSEMBLY)


    Camry. Acv40 Gsv40.Lighting.Lighting System.Lighting System Interior Light Circuit

  1. Disconnect the E25 transponder key amplifier connector.

  1. Disconnect the Q6 overhead J/B connector.

  1. Disconnect the IR and II instrument panel J/B assembly connectors.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    		Condition
    		Specified Condition
    E25-2 - Body ground
    		Always
    		10 to 14 V
    Q6-7 - Body ground
    		Always
    		10 to 14 V
    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    II-10 - E25-6
    		Always
    		Below 1 Ω
    IR-5 - Q6-6
    		Always
    		Below 1 Ω
    II-10 - Body ground
    		Always
    		10 kΩ or higher
    IR-5 - Body ground
    		Always
    		10 kΩ or higher


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY