Dtc C1251/51 Open In Pump Motor Circuit

Brake. Camry. Acv40 Gsv40
Brake Control. Camry. Acv40 Gsv40

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)

INSPECT SKID CONTROL ECU (GND2 TERMINAL)

RECONFIRM DTC

DTC C1251/51 Open in Pump Motor Circuit


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
C1251/51
  1. Actuator pump motor does not operate properly.
  2. Open in actuator pump motor circuit continues for at least 2 seconds.
  1. Brake actuator assembly (GND circuit)
  2. Brake actuator assembly (Motor circuit)

WIRING DIAGRAM


Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System. Dtc C1251/51 Open In Pump Motor Circuit


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (CAMRY_ACV40 RM000000XHR024X.html).
1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the Active Test mode on the intelligent tester.

    ABS / VSC / TRC:
    Item (Display)
    		Vehicle Condition / Test Details
    		Diagnostic Note
    Motor Relay
    		Turns ABS motor relay ON / OFF
    		Operating sound of relay (clicking sound) and motor can be heard

  1. Check the operating sound of the ABS motor relay and motor when operating it with the intelligent tester.

    OK:
    The operating sound of the ABS motor relay and motor can be heard.


OK
Go to step 3
NG


2.INSPECT SKID CONTROL ECU (GND2 TERMINAL)


    Camry. Acv40 Gsv40.Brake Control.Anti-Lock Brake System. Dtc C1251/51 Open In Pump Motor Circuit

  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    A26-1 (GND2) - Body ground
    		Always
    		Below 1 Ω


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)
OK


3.RECONFIRM DTC

  1. Reconnect the skid control ECU connector.

  1. Clear the DTC (CAMRY_ACV40 RM000000XHV02RX.html).

  1. Start the engine.

  1. Drive the vehicle at the speed of 4.3 mph (7 km/h) or more.

  1. Check if the same DTC is recorded (CAMRY_ACV40 RM000000XHV02RX.html).

    Result:

    Condition
    		Proceed to
    DTC (C1251/51) is not output
    		A
    DTC (C1251/51) is output
    		B
    HINT:
    1. If a speed signal of 4 mph (6 km/h) or more is input to the skid control ECU, with the ignition switch is turned to the ON position and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
    2. If a normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
    3. If any DTCs are output while jiggling a connector or wire harness of the brake actuator assembly (skid control ECU), inspect and repair the connector or wire harness.


B
REPLACE BRAKE ACTUATOR ASSEMBLY
A

USE SIMULATION METHOD TO CHECK