Oil Pump - Removal

1. Disconnect cable from negative battery terminal

2. Remove front wheel rh

3. Remove engine under cover rh

4. Remove engine under cover sub-assembly (for rough road area specification vehicles)

5. Drain engine oil

6. Drain engine coolant

7. Remove cylinder head cover no. 2

8. Remove fan & generator v belt

9. Remove generator assembly

10. Remove ignition coil no. 1

11. Disconnect ventilation hose

12. Disconnect ventilation hose no. 2

13. Remove cylinder head cover sub-assembly (for rhd)

14. Remove cylinder head cover sub-assembly (for lhd)

15. Remove engine mounting insulator sub-assembly rh

16. Remove crankshaft damper sub-assembly

17. Remove crankshaft position sensor

18. Remove camshaft timing oil control valve assembly (for unleaded gasoline specification vehicle)

19. Remove water pump pulley

20. Remove water pump assembly

21. Remove transverse engine engine mounting bracket

22. Remove oil pump assembly

​

NOTICE:

To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

1. Loosen the radiator drain cock plug.

2. Remove the radiator cap sub-assembly.

3. Loosen the cylinder block drain cock plug, then drain the coolant.
   

   
   
   
   

1. Remove the 4 nuts and cylinder head cover No. 2.

1. Loosen bolts A and B.

2. Release the fan and generator V belt tension and remove the fan and generator V belt.

1. Remove the terminal cap.

2. Separate the connector and harness clamp.

3. Remove the nut and remove terminal B.

4. Remove fan belt adjusting slider fixing bolts A and B and remove the fan belt adjusting slider.

5. Remove fixing bolt B and remove the generator.

1. Disconnect the 4 ignition coil connectors.

2. Remove the 4 bolts and 4 ignition coils.

1. Disconnect the ventilation hose.

1. Disconnect ventilation hose No. 2.

1. Disconnect the fuel injector connectors.

2. Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.

3. Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.

1. Disconnect the fuel injector connectors.

2. Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.

3. Remove the bolt and remove the wire harness bracket.

4. Remove the 9 bolts and 2 nuts, 2 seal washers and then remove the cylinder head cover sub-assembly.

1. Place a wooden block on a jack underneath the engine.

2. Remove the 5 bolts and nut and remove the engine mounting insulator sub-assembly RH.

1. Set cylinder No. 1 to TDC/compression.
   

   1. Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump.

   3. for Unleaded Gasoline Specification Vehicle:
      Check that the timing marks on the camshaft timing sprocket and the camshaft timing gear are all facing upward as shown in the illustration.

      HINT:

      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.

   5. for Leaded Gasoline Specification Vehicle:
      Check that both timing marks on the camshaft timing sprockets facing upward as shown in the illustration.

      HINT:

      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.

2. Using 2 SSTs, loosen the bolt while holding the crankshaft damper sub-assembly.

   SST

   09213-14010 (91651-60865)
   09330-00021
   

   NOTICE:

   Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.

3. Remove the SSTs and the bolt.

4. Remove the crankshaft damper sub-assembly.

1. Disconnect the crankshaft position sensor connector.

2. Remove the bolt and remove the crankshaft position sensor.

1. Disconnect the camshaft timing oil control valve assembly connector.

2. Remove the bolt and nut and remove the camshaft timing oil control valve assembly.

3. Remove the O-ring from the camshaft timing oil control valve assembly.

1. Using SST, hold the water pump pulley.

   SST

   09960-10010 (09962-01000, 09963-00700)
   

2. Remove the 3 bolts and remove the water pump pulley.

1. Remove the 3 bolts and 2 nuts and remove the water pump assembly and gasket.

1. Remove the 4 bolts and remove the transverse engine engine mounting bracket.

1. Remove the 15 bolts and the nut.

2. Using a screwdriver with its tip wrapped in protective tape, prize the oil pump assembly to remove it.

   NOTICE:

   Do not damage the contact surfaces of the oil pump assembly and oil pan sub-assembly.

3. Remove the 2 O-rings from the cylinder block and oil pan sub-assembly.