Toyota
Yaris NCP90 91 92 93
Repair Manual
1Nz-Fe Engine Control System
Ecm
Remove front wiper arm and blade assembly lh (for hatchback)
Remove front wiper arm and blade assembly rh (for hatchback)
Remove cowl top ventilator louver sub-assembly (for hatchback lhd)
Remove cowl top ventilator louver sub-assembly (for hatchback rhd)
Remove cowl top ventilator louver sub-assembly (for sedan rhd)
Remove cowl top ventilator louver sub-assembly (for sedan lhd)
Remove cowl to register duct sub-assembly no. 2 (for hatchback)
- NOTICE:
- Replace the ECM with a new one if necessary.

Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.

Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

Remove the nut and front wiper arm.

Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
- HINT:
- Use the same procedure as for the LH side.
- HINT:
- Use the same procedure as for the LH side.
![]() |
Disengage the 7 clips and remove the hood to cowl top seal.

Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.
- HINT:
- Use the same procedure as for the LH side.
![]() |
Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

Disconnect the washer hose.
Disengage the 11 claws and clip.

Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.
![]() |
Remove the 2 clips.
Disengage the 4 claws and remove the cowl top ventilator louver LH.
![]() |
Disconnect the washer hose.
Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.
![]() |
Remove the clip.
Disengage the 4 claws and remove the cowl top ventilator louver LH.

Disengage the 2 clips, the 6 claws and the 10 hooks.
Remove the cowl top ventilator louver sub-assembly.

Disconnect the washer hoses.
Disengage the 5 hooks.

Disengage the 3 clips, the 4 claws and the 8 hooks.
Remove the cowl top ventilator louver sub-assembly.

Disconnect the washer hoses.
Disengage the 5 hooks.
![]() |
Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.

Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.
![]() |
Disengage the claw and remove cowl to register duct sub-assembly No. 2.
![]() |
Disengage 3 claws and remove the front air shutter seal.
![]() |
Disengage the wire harness clamp.

Remove the 9 bolts and remove the cowl top panel outer.
![]() |
Disengage the claw and disconnect the wire harness.

Remove the 2 bolts and remove the cowl top panel outer center bracket.

Remove the 8 bolts and remove the cowl top panel outer.
![]() |
Remove the 2 lock knobs and harness clamp.
Disconnect the 2 ECM connectors.

Remove the bolt and 2 nuts and remove the ECM.
![]() |
Remove the 2 screws and the ECM bracket.
![]() |
Remove the 2 screws and ECM bracket No. 2.












