Power Window Regulator Motor - Removal(2006/01 - 2007/12)

1. Remove front door lower frame bracket garnish

2. Remove front door inside handle bezel plug

3. Remove assist grip cover

4. Remove courtesy light assembly

5. Remove front door trim board sub-assembly

6. Remove front door inside handle sub-assembly

7. Remove front door inner glass weatherstrip

8. Remove front no. 1 speaker assembly

9. Remove front door service hole cover

10. Remove front door glass sub-assembly

11. Remove front door window regulator sub-assembly

12. Remove front power window regulator motor assembly

13. Remove rear door inside handle bezel plug

14. Remove door assist grip cover

15. Remove rear ash receptacle assembly

16. Remove rear door trim board sub-assembly

17. Remove rear door inside handle sub-assembly

18. Remove rear door inner glass weatherstrip

19. Remove rear door service hole cover

20. Remove rear door glass run

21. Remove rear door lower window frame sub-assembly

22. Remove rear door quarter window glass

23. Remove rear door glass sub-assembly

24. Remove rear door window regulator sub-assembly

25. Remove rear power window regulator motor assembly

​

1. Disengage the 2 clips and remove the front door lower frame bracket garnish.

1. Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.

1. Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the assist grip cover.

1. Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.

2. Disconnect the connector.

1. Remove the 3 screws and clip (A).

2. Using a clip remover, disengage the 9 clips.

3. Pull up the front door trim board in the direction indicated by the arrow.

4. Disengage the reference bosses from the front door panel.

5. Raise the front door trim board to disengage the 4 claws and remove the front door trim board together with the front door inner glass weatherstrip.

6. Disengage the 2 claws and disconnect the front door inside handle sub-assembly.

1. Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door inside handle sub-assembly.

1. Using a screwdriver, disengage the 4 clips as shown in the illustration and remove the front door inner glass weatherstrip from the front door trim board.

1. Disconnect the connector.

2. Remove the 4 bolts and front No. 1 speaker assembly.

   NOTICE:

   Do not touch the cone part of the speaker.

1. Disconnect the connector and each clamp, and remove the front door service hole cover.

   HINT:

   Remove the remaining butyl tape on the door side.

1. Connect the front power window regulator motor assembly connector.

2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

3. Remove the 2 bolts.

   NOTICE:

   After the bolts are removed, the door glass may fall, causing damage.

4. Remove the front door glass sub-assembly as shown in the illustration.

   NOTICE:

   Do not damage the door glass.

5. Disconnect the power window regulator master switch assembly and front power window regulator motor assembly connector.

1. Loosen the temporary bolt.

   NOTICE:

   Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall, causing damage.

2. Remove the 5 bolts.

3. Remove the front door window regulator sub-assembly and the power window regulator motor assembly front as a unit.

4. Remove the temporary bolt from the front door window regulator sub-assembly.

1. Using a "TORX" driver (T25), remove the 3 screws and the front power window regulator motor assembly.

1. Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.

1. Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the door assist grip cover.

1. Remove the rear ash receptacle assembly.

1. Remove the 3 screws.

2. Using a clip remover, disengage the 7 clips.

3. Raise the rear door trim board to disengage the 4 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.

4. Disconnect the connector.

5. Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.

6. Disengage the clip as shown in the illustration and remove the No. 1 door scuff plate clamp from the rear door trim board.

1. Disconnect the cables and remove the rear door inside handle sub-assembly.

1. Disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.

1. Disconnect the connector.

2. Remove the rear door service hole cover.

   HINT:

   Remove the remaining tape on the door side.

1. Remove the rear door glass run.

1. Remove the 2 bolts, the screw, and the rear door lower window frame sub-assembly.

1. Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

   NOTICE:

   Do not damage the door glass.

1. Disconnect the connector.

2. Loosen the temporary bolt.

   NOTICE:

   Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall, causing damage.

3. Remove the 3 bolts.

4. Remove the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.

5. Remove the temporary bolt from the rear door window regulator.

1. Using a "TORX" driver (T25), remove the 3 screws and the rear power window regulator motor assembly.