Roof Headlining - Installation(2010/08 - )

1. Install no. 1 roof wire (w/o sliding roof)

2. Install no. 1 roof wire (w/ sliding roof)

3. Install antenna cord sub-assembly

4. Install vanity light assembly

5. Install fastener hook (w/ sliding roof)

6. Install no. 2 rear side rail spacer lh (w/ sliding roof)

7. Install no. 2 rear side rail spacer rh (w/ sliding roof)

8. Install no. 4 roof silencer pad (w/o sliding roof)

9. Install no. 2 roof silencer pad (w/o sliding roof)

10. Install roof side rail silencer pad lh (w/o sliding roof)

11. Install roof side rail silencer pad rh (w/o sliding roof)

12. Install no. 3 rear side rail spacer lh (w/o sliding roof)

13. Install no. 3 rear side rail spacer rh (w/o sliding roof)

14. Install no. 2 rear side rail spacer lh (w/o sliding roof)

15. Install no. 2 rear side rail spacer rh (w/o sliding roof)

16. Install radio setting condenser

17. Install roof headlining assembly (w/o sliding roof)

18. Install roof headlining assembly (w/ sliding roof)

19. Install sunshade trim holder (w/ rear sunshade)

20. Install sun roof opening trim moulding (w/ sliding roof)

21. Install spot light assembly (w/ sliding roof)

22. Install no. 1 room light assembly (w/o sliding roof)

23. Install front assist grip sub-assembly

24. Install rear assist grip sub-assembly

25. Install visor holder

26. Install visor assembly lh

27. Install visor assembly rh

28. Install roof console box assembly

29. Install front pillar garnish lh

30. Install front pillar garnish rh

31. Install roof side inner garnish lh

32. Install roof side inner garnish rh

33. Install upper center pillar garnish lh

34. Install lower center pillar garnish lh

35. Connect front seat outer belt assembly lh

36. Install lap belt outer anchor cover (for lh side)

37. Install front door opening trim weatherstrip lh

38. Install cowl side trim sub-assembly lh

39. Install front door scuff plate lh

40. Install upper center pillar garnish rh

41. Install lower center pillar garnish rh

42. Connect front seat outer belt assembly rh

43. Install lap belt outer anchor cover (for rh side)

44. Install front door opening trim weatherstrip rh

45. Install cowl side trim sub-assembly rh

46. Install front door scuff plate rh

47. Install rear door inner glass weatherstrip lh

48. Install rear door trim board sub-assembly lh

49. Install door assist grip cover lh

50. Install rear door inside handle bezel plug lh

51. Install reclining remote control lever sub-assembly lh (for reclining seat type)

52. Install reclining remote control lever sub-assembly rh (for reclining seat type)

53. Install rear door opening trim weatherstrip lh

54. Install rear door scuff plate lh

55. Install rear door opening trim weatherstrip rh

56. Install rear door scuff plate rh

57. Install center seatback assembly (for reclining seat type)

58. Install separate type rear seatback assembly lh (for reclining seat type)

59. Install separate type rear seatback assembly rh (for reclining seat type)

60. Install rear seatback cover (for reclining seat type)

61. Install rear side seatback assembly lh (for fold down seat type)

62. Install rear side seatback assembly rh (for fold down seat type)

63. Install separate type rear seatback assembly lh (for fold down seat type)

64. Install separate type rear seatback assembly rh (for fold down seat type)

65. Install rear center seat headrest assembly

66. Install rear seat headrest assembly

67. Install rear seat cushion assembly

68. Install front seat assembly lh (for power seat)

69. Install inner seat track bracket cover rh (for power seat)

70. Install seat track cover lh (for power seat)

71. Install front seat headrest assembly (for power seat)

72. Install front seat assembly lh (for manual seat)

73. Install inner seat track bracket cover lh (for manual seat)

74. Install seat track cover lh (for manual seat)

75. Install front seat headrest assembly (for manual seat)

76. Install front seat assembly rh (for power seat)

77. Install inner seat track bracket cover lh (for power seat)

78. Install seat track cover rh (for power seat)

79. Install front seat headrest assembly (for power seat)

80. Install front seat assembly rh (for manual seat)

81. Install inner seat track bracket cover rh (for manual seat)

82. Install seat track cover rh (for manual seat)

83. Install front seat headrest assembly (for manual seat)

84. Connect cable to negative battery terminal (for manual seat)

85. Inspect srs warning light

86. Inspect front seat assembly (for power seat)

87. Inspect slide adjuster lock (for manual seat)

​

1. Apply new double-sided tape to locations shown in the illustration while aligning the tape with the markings on the roof headlining.
   

   
   
   
   

   NOTICE:

   Securely apply the double-sided tape to prevent it from being out of alignment and peeling off.

2. Peel off the release paper from the double-sided tape.

3. Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.

   NOTICE:

   Securely attach the No. 1 roof wire. Failure to do so may cause abnormal noise.

4. Turn the visor connectors clockwise approximately 90° to install the connectors to the roof headlining.

5. Apply adhesive tape to locations shown in the illustration.
   

   
   
   
   

   HINT:

   As shown at point A in the illustration, line up and secure the reference tape of the wire harness to the tip of the roof headlining assembly.

1. Apply new double-sided tape to locations shown in the illustration while aligning the tape with the markings on the roof headlining.
   

   
   
   
   

   NOTICE:

   Securely apply the double-sided tape to prevent it from being out of alignment and peeling off.

2. Peel off the release paper from the double-sided tape.

3. Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.

   NOTICE:

   Securely attach the No. 1 roof wire. Failure to do so may cause abnormal noise.

4. Turn the visor connectors clockwise approximately 90° to install the connectors to the roof headlining.

5. Apply adhesive tape to locations shown in the illustration.
   

   
   
   
   

   HINT:

   As shown at point A in the illustration, line up and secure the reference tape of the wire harness to the tip of the roof headlining assembly.

HINT:

The double-sided tape and tape are not available as supply parts. If these tapes still have enough adhesion to secure the roof headlining and antenna cord, reuse the tapes. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedures below.

1. Apply new double-sided tape.
   

   
   
   
   
   

   1. Remove the double-sided tape from the roof headlining assembly.

   2. Peel off the appropriate amount of new double-sided tape. Be careful not to touch the adhesive surface.

   3. Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.

   4. Peel off the backing sheet from the double-sided tape.

2. Install the antenna cord to the roof headlining assembly from the front of the vehicle.
   

   
   
   
   

3. Put the strips of the tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.

   HINT:

   1. If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.
      
   2. For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.
      
   3. For the right rear corner of the roof headlining assembly, align the marking tape on the antenna cord with the rear edge of the roof headlining, and secure the antenna cord to the roof headlining assembly with tape.
      
   4. For the part of the antenna cord near the center of the roof headlining assembly, position the marking tape on the antenna cord within the area indicated by the marking line. Secure the antenna cord to the roof headlining assembly with tape as shown in the illustration. (without sliding roof)
      

1. Engage the 3 claws and install the vanity light assembly.

1. Align the markings on the roof headlining assembly with the fastener hooks and install the fastener hooks using hot melt glue as shown in the illustration.

1. Align the markings on the roof headlining assembly with the No. 2 rear side rail spacer LH and install the spacer using hot melt glue as shown in the illustration.

HINT:

Use the same procedures for the RH side and the LH side.

1. Align the markings on the roof headlining assembly with the No. 4 roof silencer pads and install the silencer pads using hot melt glue or double-sided tape as shown in the illustration.

1. Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the silencer pad using hot melt glue or double-sided tape as shown in the illustration.

1. Align the markings on the roof headlining assembly with the roof side rail silencer pad LH and install the silencer pad using hot melt glue as shown in the illustration.

HINT:

Use the same procedures for the RH side and the LH side.

1. Align the markings on the roof headlining assembly with the No. 3 rear side rail spacer LH and install the spacer using hot melt glue as shown in the illustration.

HINT:

Use the same procedures for the RH side and the LH side.

1. Align the markings on the roof headlining assembly with the No. 2 rear side rail spacer LH and install the spacer using hot melt glue as shown in the illustration.

HINT:

Use the same procedures for the RH side and the LH side.

1. Using an air riveter or hand riveter with a nose piece, install the radio setting condenser with a new rivet.
   

   
   
   
   

   NOTICE:

   1. Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
      
   2. Confirm that the rivet is seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.
      
   3. Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.
      

   HINT:

   If the rivet cannot be cut, pull it once and cut it.

1. Pull the roof headlining assembly into the vehicle through the rear left door.

2. Engage the 4 clips.

3. Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

4. Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

5. Install the radio setting condenser to the front pillar RH with the bolt.

6. Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.
   

   
   
   
   

1. Pull the roof headlining assembly into the vehicle through the rear left door.

2. Engage the hook, 4 clips, and 2 fasteners.

3. Connect the sliding roof drive gear connector.

4. Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

5. Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

6. Install the radio setting condenser to the front pillar RH with the bolt.

7. Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.
   

   
   
   
   

1. Engage the 2 claws.

2. Using a screwdriver, turn the pin of each sunshade trim holder 90°to install the sunshade trim holders.

1. Align the paint mark on the inner surface of the opening trim moulding with the notch of the roof headlining, and install the sun roof opening trim moulding so that joining point of the opening trim is on the left side of the vehicle as shown in the illustration.

   NOTICE:

   After installation, check that the corners fit correctly.

1. Push the light bulb holder in the direction indicated by the arrow in the illustration to engage the claw.

2. Engage the 4 claws.

3. Engage the 6 claws and install the spot light assembly.

1. Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.

2. Engage the 4 claws.

3. Engage the 4 claws and install the lens cover.

1. Assemble the front assist grip sub-assembly as shown in the illustration.

2. Install the front assist grip sub-assembly.

   HINT:

   Use the same procedures for the RH side and the LH side.

HINT:

Use the same procedures for the rear side and the front side.

1. Engage the 2 claws.

2. Push in the visor holder and turn it approximately 45°as shown in the illustration.
   

   
   
   
   

1. Engage the 2 clips and install the visor assembly LH.

2. Engage the 4 claws and install the visor bracket cover.

HINT:

Use the same procedures for the RH side and the LH side.

1. Connect the connectors.

2. Engage the 2 claws and 2 clips, and then install the roof console box assembly.

1. Remove the protective cover.

2. Install a new clip <A> on the front pillar garnish LH.

3. Engage the 2 claws and 2 clips, then install the front pillar garnish LH.

1. Remove the protective cover.

2. Install a new clip <A> on the front pillar garnish RH.

3. Engage the 2 claws and 2 clips, then install the front pillar garnish RH.

1. Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.

HINT:

Use the same procedures for the RH side and the LH side.

1. Engage the clip.

2. Install the upper center pillar garnish LH with the bolt.

1. Engage the 2 claws and 2 clips, then install the lower center pillar garnish LH.

1. Install the floor end of the front seat outer belt assembly LH with the bolt.

   Torque:

   42 N*m{428 kgf*cm, 31 ft.*lbf}

1. Engage the 3 claws and install the lap belt outer anchor cover.

1. Install the front door opening trim weatherstrip LH as shown in the illustration.

   NOTICE:

   After installation, check that the corners fit correctly.

1. Engage the 2 clips.

2. Install the cowl side trim sub-assembly LH with the cowl side trim clip.

1. Engage the 7 claws and 3 clips, then install the front door scuff plate LH.

HINT:

Use the same procedures for the RH side and the LH side.

HINT:

Use the same procedures for the RH side and the LH side.

HINT:

Use the same procedures for the RH side and the LH side.

HINT:

Use the same procedures for the RH side and the LH side.

1. Install the front door opening trim weatherstrip RH as shown in the illustration.

   NOTICE:

   After installation, check that the corners fit correctly.

HINT:

Use the same procedures for the RH side and the LH side.

HINT:

Use the same procedures for the RH side and the LH side.

1. Engage the 3 claws to install the rear door inner glass weatherstrip.

1. Engage the claw to install the No. 1 door scuff plate clamp.

2. Connect each connector.

3. Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.

4. Engage the 7 clips to install the rear door trim board to the rear door panel.

5. Install the 3 screws.

1. Engage the 6 claws and install the door assist grip cover.

1. Engage the 3 claws to install the rear door inside handle bezel plug.

1. Install the rear seat reclining control cable.

2. Engage the 2 clips and claw and then install the reclining remote control lever sub-assembly.

3. Install the bolt.

   Torque:

   18 N*m{184 kgf*cm, 13 ft.*lbf}

4. Adjust the control lever to set the rear reclining adjuster assembly to its upper most position.

5. Pull plate A toward the front of the vehicle to lock the plate.

1. Install the rear door opening trim weatherstrip LH as shown in the illustration.

   NOTICE:

   After installation, check that the corners fit correctly.

1. Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.

1. Install the rear door opening trim weatherstrip RH as shown in the illustration.

   NOTICE:

   After installation, check that the corners fit correctly.

HINT:

Use the same procedures for the RH side and the LH side.

1. Install the center seatback assembly with the 2 bolts.

   Torque:

   18 N*m{184 kgf*cm, 13 ft.*lbf}

1. Install the separate type rear seatback assembly LH with the 2bolts and 2 nuts.

   Torque:

   18 N*m{184 kgf*cm, 13 ft.*lbf}

2. Engage the 3 clamps and install the cover.

3. Install the 2 rear seat belts.

1. Install the separate type rear seatback assembly RH with the 2 bolts and 2 nuts.

   Torque:

   18 N*m{184 kgf*cm, 13 ft.*lbf}

2. Engage the 3 clamps and install the cover.

3. Install the rear seat belt.

1. Install the rear side seatback assembly with the bolt.

   Torque:

   18 N*m{184 kgf*cm, 13 ft.*lbf}

1. Install the separate type rear seatback assembly with the 2 bolts.

   Torque:

   18 N*m{184 kgf*cm, 13 ft.*lbf}

1. Install the separate type rear seat back assembly with the 2 bolts.

   Torque:

   18 N*m{184 kgf*cm, 13 ft.*lbf}

1. Attach the front hooks of the bench type rear seat cushion assembly to the vehicle body.

2. Confirm that the seat cushion is firmly installed.

   NOTICE:

   When installing the bench type rear seat cushion assembly, make sure that the seat belt buckle is not under the bench type rear seat cushion assembly.

1. Place the seat in the cabin.

2. Connect the connectors under the seat.

3. Connect the cable to the negative (-) battery terminal.

4. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

   NOTICE:

   Check that the seat is locked.

5. Temporarily install the front side of the front seat assembly with the 2 bolts.

6. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

   NOTICE:

   Check that the seat is locked.

7. Temporarily install the rear side of the front seat assembly with the 2 bolts.

8. Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.

   NOTICE:

   Check that the seat is locked.

9. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

   Torque:

   37 N*m{377 kgf*cm, 27 ft.*lbf}

10. Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.

    NOTICE:

    Check that the seat is locked.

11. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.

    Torque:

    37 N*m{377 kgf*cm, 27 ft.*lbf}

1. Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

2. Push the inner seat track bracket cover to engage claw B.

1. Slide the seat track cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

2. Push the seat track cover to engage claw B.

1. Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.

2. Connect the connector and clamp.

3. Move the front seat assembly to the rearmost position by operating the slide handle.

   NOTICE:

   Check that the seat is locked.

4. Temporarily install the front seat track bracket with the 2 bolts.

5. Move the front seat assembly fully forward by operating the slide handle.

   NOTICE:

   Check that the seat is locked.

6. Temporarily install the rear seat track bracket with the 2 bolts.

7. Move the front seat assembly to the rearmost position by operating the slide handle.

   NOTICE:

   Check that the seat is locked.

8. Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.

   Torque:

   37 N*m{377 kgf*cm, 27 ft.*lbf}

9. Move the front seat assembly fully forward by operating the slide handle.

   NOTICE:

   Check that the seat is locked.

10. Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:

    37 N*m{377 kgf*cm, 27 ft.*lbf}

1. Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

2. Push the seat track bracket cover inner to engage claw B.

1. Slide the seat track cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

2. Push the seat track cover to engage claw B.

HINT:

Use the same procedures for the RH side and the LH side.

HINT:

Use the same procedures for the RH side and the LH side.

HINT:

Use the same procedures for the RH side and the LH side.

HINT:

Use the same procedures for the RH side and the LH side.

HINT:

Use the same procedures for the RH side and the LH side.

HINT:

Use the same procedures for the RH side and the LH side.

1. Check the power seat operation.

2. Check the seat heater operation (with seat heater system).
   

   1. Turn the ignition switch on (IG).

   2. Turn the seat heater switch ON.

   3. Wait 5 minutes or more and confirm that the seat surface becomes warm.