Lighting System - Rear Fog Light Circuit

Brand:

Toyota

Model Name:

Camry ACV40 GSV40

Manual:

Repair Manual

Section:

Lighting

Title:

Lighting System

  1. Description

  2. Wiring diagram

  3. Inspection procedure

  4. Perform active test using intelligent tester

  5. Inspect fuse (rr fog)

  6. Inspect rear fog light relay

  7. Inspect instrument panel junction block assembly

  8. Check harness and connector (instrument panel j/b assembly - rear fog light relay)

  9. Check harness and connector (rear fog light relay - main body ecu)

  10. Check harness and connector (battery - rear fog light relay)

LIGHTING SYSTEM > Rear Fog Light Circuit


​

DESCRIPTION

When the taillights are on and the rear fog light switch is turned on, the main body ECU turns the rear fog lights on.

WIRING DIAGRAM


Connect the intelligent tester to the DLC3. Camry


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Turn the light control switch to the TAIL position.

  1. Select the item below in the ACTIVE TEST and then check that the relay operates.

    Main Body (Main Body ECU):
    Item
    Test Details
    Diagnostic Note
    Rear Fog Light Relay
    Rear fog light relay ON/OFF
    -
    OK:
    Rear fog light relay operates. (Rear fog lights come on)


OKnext
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG
next down

2.INSPECT FUSE (RR FOG)
  1. Remove the RR FOG fuse from the engine room R/B.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω


NGnext
REPLACE FUSE
OK
next down

3.INSPECT REAR FOG LIGHT RELAY
  1. Remove the rear fog light relay from the engine room No. 2 J/B. Camry
  2. Remove the rear fog light relay from the engine room No. 2 J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    Below 1 Ω (When battery voltage is applied to terminals 1 and 2)


NGnext
REPLACE REAR FOG LIGHT RELAY
OK
next down

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Measure the voltage according to the value(s) in the table below.Standard voltage:Tester ConnectionConditionSpecified ConditionE8-14 - Body groundLight control switch in TAIL and rear fog light switch OFF → ON10 to 14 V → Below 1 V Camry
  2. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-14 - Body ground
    Light control switch in TAIL and rear fog light switch OFF → ON
    10 to 14 V → Below 1 V


OKnext
Go to step 7
NG
next down

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B ASSEMBLY - REAR FOG LIGHT RELAY)
  1. Remove the rear fog light relay from the engine room No. 2 relay block. Camry
  2. Remove the rear fog light relay from the engine room No. 2 relay block.

  1. Measure the voltage on the relay block side according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Rear fog light relay terminal 2 - Body ground
    Light control switch OFF → TAIL
    10 to 14 V


NGnext
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
next down

6.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - MAIN BODY ECU)
  1. Disconnect the E8 main body ECU connector. Camry
  2. Disconnect the E8 main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-14 - Body ground
    Light control switch OFF → TAIL
    Below 1 V → 10 to 14 V


NGnext
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
next down
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BATTERY - REAR FOG LIGHT RELAY)
  1. Remove the rear fog light relay from the engine room No. 2 relay block. Camry
  2. Remove the rear fog light relay from the engine room No. 2 relay block.

  1. Measure the voltage on the relay block side according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Rear fog light relay terminal 5 - Body ground
    Always
    10 to 14 V


NGnext
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - REAR FOG LIGHT RELAY)
OK
next down
REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR FOG LIGHT RELAY - BODY GROUND)