Power Window Control System (For Models With Jam Protection Function On 4 Windows) - Front Passenger Side Power Window Does Not Operate With Front Passenger Side Power Window Switch(2009/01 - 2010/08)

1. Description

2. Wiring diagram

3. Inspection procedure

4. Read value using intelligent tester (main body)

5. Read value using intelligent tester (p-door motor)

6. Perform active test using intelligent tester (p-door motor)

7. Inspect power window regulator switch assembly (for front passenger side)

8. Check harness and connector (front passenger side switch - motor and body ground)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows) > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

​

DESCRIPTION

HINT:

If the pulse sensor built into the power window regulator motor assembly (for front passenger side) malfunctions, the power window control system enters fail-safe mode. The remote up/down and auto up/down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly (for front passenger side) at the auto up position, and opened manually by pushing down the power window regulator switch assembly (for front passenger side).

WIRING DIAGRAM

INSPECTION PROCEDURE

NOTICE:

1. The power window control system uses a multiplex communication system (LIN communication system). Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.
   
2. When the power window regulator motor assembly (for front passenger side) is reinstalled or replaced, the power window control system must be initialized.
   
3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be reinitialized by repeating the following operations at least 5 times:
   
4. 1. Close the power window by fully pulling up the power window regulator switch assembly (for front passenger side) and holding it at the auto up position.
      
   2. Open the power window by fully pushing down the power window regulator switch assembly (for front passenger side).
      
5. When the ECU determines that the power window regulator motor assembly (for front passenger side) has a malfunction, DTC B2311 is set.
   

1. Connect the intelligent tester to the DLC3.

2. Turn the ignition switch to ON.

3. Turn the intelligent tester on.

4. Enter the following menus: Body / Main Body / Data List.

5. Read the Data List according to the display on the intelligent tester.
   

   Main Body (Main Body ECU (Instrument Panel J/B))

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Communication P-Door Motor	Connection status between power window regulator motor (for front passenger side) and main body ECU (instrument panel J/B) / OK or STOP	OK: Normal communication STOP: Communication stopped	-

   OK:

   On the intelligent tester screen, OK is displayed.
   

NG	GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting) (Click here)

OK

1. Enter the following menus: Body / P-Door Motor / Data List.

2. Read the Data List according to the display on the intelligent tester.
   

   P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Side))

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   P Door P/W Up SW	Front passenger side power window manual up switch signal / ON or OFF	ON: Front passenger door power window manual up switch operated OFF: Front passenger power window manual up switch not operated	-
   P Door P/W Down SW	Front passenger side power window manual down switch signal / ON or OFF	ON: Front passenger door power window manual down switch operated OFF: Front passenger power window manual down switch not operated	-

   OK:

   On the intelligent tester screen, ON or OFF is displayed accordingly.
   

NG	Go to step 4

OK

1. Enter the following menus: Body / P-Door Motor / Active Test.

2. Perform the Active Test according to the display on the intelligent tester.
   

   P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Side))

   Tester Display	Test Part	Control Range	Diagnostic Note
   Power Window	Power window	OFF / UP / DOWN	-

   OK:

   Front passenger side power window operates normally.
   

   CAUTION:

   Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

NG	REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side) (Click here)

OK
REPLACE MAIN BODY ECU (INSTRUMENT PANEL J/B)

1. Remove the power window regulator switch assembly (for front passenger side) (Click here).

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance:

   Tester Connection	Switch Condition	Specified Condition
   6 (UP) - 1 (GND)	Auto up or up position	Below 1 Ω
   7 (DOWN) - 1 (GND)	Auto down or down position	Below 1 Ω

NG	REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side) (Click here)

OK

1. Disconnect the power window regulator motor assembly (for front passenger side) connector.

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance:

   Tester Connection	Condition	Specified Condition
   H13-6 (UP) - H12-10 (UP)	Always	Below 1 Ω
   H13-7 (DOWN) - H12-7 (DOWN)	Always	Below 1 Ω
   H13-1 (GND) - Body ground	Always	Below 1 Ω
   H13-6 (UP) - Body ground	Always	10 kΩ or higher
   H13-7 (DOWN) - Body ground	Always	10 kΩ or higher
   H12-10 (UP) - Body ground	Always	10 kΩ or higher
   H12-7 (DOWN) - Body ground	Always	10 kΩ or higher

NG	REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side) (Click here)