Airbag System - Srs Warning Light Remains On(2007/12 - 2009/01)

Brand:

Toyota

Model Name:

Camry ACV40 GSV40

Manual:

Repair Manual

Section:

Supplemental Restraint System

Title:

Airbag System

  1. Description

  2. Wiring diagram

  3. Inspection procedure

  4. Check can communication system

  5. Check battery

  6. Check connectors

  7. Check wire harness (source voltage of center airbag sensor assembly)

  8. Check wire harness (source voltage of combination meter assembly)

  9. Check srs warning light

AIRBAG SYSTEM > SRS Warning Light Remains ON


​

DESCRIPTION

The SRS warning light is located on the combination meter assembly.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from the LOCK to the ON position, and then goes off automatically.
If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.
When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor assembly in case the source voltage drops.
When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.
A malfunction in this circuit is not recorded in the center airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.
The signal to illuminate the SRS warning light is transmitted from the center airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM


Check if a CAN communication DTC is output (Click herefor LHD, Click here for RHD).Result:ConditionProceed ToDTC is not outputADTC is outputB Camry


Check if a CAN communication DTC is output (Click herefor LHD, Click here for RHD).Result:ConditionProceed ToDTC is not outputADTC is outputB Camry


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click herefor LHD, Click here for RHD).

    Result:

    Condition
    Proceed To
    DTC is not output
    A
    DTC is output
    B


Bnext
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A
next down

2.CHECK BATTERY
  1. Measure the voltage of the battery.

    Standard voltage:
    11 to 14 V


NGnext
CHECK AND REPLACE BATTERY OR CHARGING SYSTEM
OK
next down

3.CHECK CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and combination meter assembly.

    OK:
    The connectors are properly connected.


NGnext
CONNECT CONNECTORS PROPERLY
OK
next down

4.CHECK WIRE HARNESS (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR ASSEMBLY)
  1. Disconnect the connectors from the center airbag sensor assembly. Camry
  2. Disconnect the connectors from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Operate all components of the electrical system (defogger, wipers, headlight, heater blower, etc.).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E30-21 (IG2) - Body ground
    Ignition switch ON
    10 to 14 V
  1. Turn the ignition switch to the LOCK position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E30-25 (E1) - Body ground
    Always
    Below 1 Ω
    E30-26 (E2) - Body ground
    Always
    Below 1 Ω


NGnext
REPAIR OR REPLACE WIRE HARNESS
OK
next down

5.CHECK WIRE HARNESS (SOURCE VOLTAGE OF COMBINATION METER ASSEMBLY)
  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds. Camry
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the F1 connector from the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F1-1 (B2) - Body ground
    Always
    10 to 14 V
    F1-2 (B) - Body ground
    Ignition switch ON
    10 to 14 V
    F1-13 (IG+) - Body ground
    Ignition switch ON
    10 to 14 V
  1. Turn the ignition switch to the LOCK position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F1-12 (E2) - Body ground
    Always
    Below 1 Ω
    F1-24 (ES) - Body ground
    Always
    Below 1 Ω


NGnext
REPAIR OR REPLACE WIRE HARNESS
OK
next down

6.CHECK SRS WARNING LIGHT
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Check the SRS warning light condition.

    OK:
    After the primary check period, SRS warning light goes off for approximately 10 seconds, and comes on.
    HINT:
    The primary check period shows approximately 6 seconds after the ignition switch is turned to the ON position.


NGnext
GO TO METER / GAUGE SYSTEM (Click here)
OK
next down
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)