Hood Lock Control Cable Assembly - Removal(2006/01 - 2007/12)

1. Remove front wheel

2. Remove cool air intake duct seal (for 2gr-fe)

3. Remove front bumper assembly (w/o headlight cleaner system)

4. Remove front bumper assembly (w/ headlight cleaner system)

5. Remove front fender liner (w/o front fender mudguard)

6. Remove front fender mudguard sub-assembly (w/ front fender mudguard)

7. Remove front fender liner (w/ front fender mudguard)

8. Remove high pitched horn assembly

9. Remove hood lock assembly

10. Remove hood lock control lever sub-assembly (for lhd)

11. Remove hood lock control lever sub-assembly (for rhd)

12. Remove hood lock control cable assembly (for lhd)

13. Remove hood lock control cable assembly (for rhd)

​

1. Remove the 7 clips and intake duct seal.

1. Put protective tape around the front bumper assembly.

2. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

   HINT:

   Use the same procedures for the RH side and LH side.

3. Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.

4. Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

   HINT:

   Use the same procedures for the RH side and LH side.

5. Disconnect each connector, and then remove the front bumper assembly.

1. Put protective tape around the front bumper assembly.

2. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

   HINT:

   Use the same procedures for the RH side and LH side.

3. Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.

4. Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

   HINT:

   Use the same procedures for the RH side and LH side.

5. Disconnect each connector.

6. Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.

1. Remove the 5 clips and bolt.

2. Remove the 5 screws, grommet and the front fender liner.

1. Remove the 3 screws and front fender mudguard sub-assembly.

1. Remove the 4 clips and bolt.

2. Remove the 3 screws, grommet and the front fender liner.

1. Disconnect the connector.

2. Remove the bolt and the high pitched horn assembly.

1. Disconnect the connector.

2. Remove the 3 bolts.

3. Disconnect the hood lock control cable.

4. Remove the hood lock assembly.

1. Disconnect the hood lock control cable and remove the hood lock control lever.

1. Disconnect the hood lock control cable and remove the hood lock control lever.

1. Using a screwdriver, disconnect the clamps shown in the illustration.
   

   
   
   
   
   

   Area	Part Name	Area	Part Name
   A	Hood lock control cable	H	Grommet
   B	Clamp	I	Side member outer
   C	Wire harness	J	Radiator
   D	Pillar	K	Radiator support cover (for 2GR-FE)
   E	Nut	L	Front fender apron
   F	Radiator support upper	M	Brace
   G	Hood lock protector	-	-

   HINT:

   Tape the screwdriver tip before use.

2. Pull the cable from the engine compartment and remove it.

1. Using a screwdriver, disconnect the clamps shown in the illustration.
   

   
   
   
   
   

   Area	Part Name	Area	Part Name
   A	Hood lock control cable	G	Side member outer
   B	Clamp	H	Radiator
   C	Washer hose	I	Radiator support cover (for 2GR-FE)
   D	Radiator support upper	J	Front fender apron
   E	Hood lock protector	K	Brace
   F	Grommet	L	Pillar

   HINT:

   Tape the screwdriver tip before use.

2. Pull the cable from the engine compartment and remove it.