Sfi System - P0504(2006/01 - 2009/01)

Brand:

Toyota

Model Name:

Camry ACV40 GSV40

Manual:

Repair Manual

Section:

2Az-Fe Engine Control System

Title:

Sfi System

  1. Description

  2. Wiring diagram

  3. Inspection procedure

  4. Check stop light switch (terminal voltage)

  5. Inspect stop light switch

  6. Check ecm (stp and st1 - voltage)

  7. Inspect fuse (stop and ign fuses)

DTC P0504 Brake Switch "A" / "B" Correlation


​

DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:
The normal conditions are as shown in the table below. The signals can be read using the intelligent tester.

Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch to the ON position
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. STOP fuse
  4. IGN fuse
  5. ECM

WIRING DIAGRAM


Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred. Camry


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. STP signal conditions can be checked using the intelligent tester.
    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch to the ON position and turn the tester on.
    3. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.
    4. Check the STP signal when the brake pedal is depressed and released.

      Brake Pedal Operation
      		Specified Condition
      Depressed
      		STP signal ON
      Released
      		STP signal OFF
1.CHECK STOP LIGHT SWITCH (TERMINAL VOLTAGE)
  1. Disconnect the A19 stop light switch connector. Camry

  2. Disconnect the A19 stop light switch connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage between the terminals of the stop light switch connector and body ground.

    Standard voltage:
    Tester Connection
    		Specified Condition
    B (A19-2) - Body ground
    		9 to 14 V
    B (A19-3) - Body ground
    		9 to 14 V

  1. Reconnect the stop light switch connector.



NGnext
Go to step 4
OK
next down

2.INSPECT STOP LIGHT SWITCH
  1. Remove the stop light switch. Camry

  2. Remove the stop light switch.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    		Switch Position
    		Specified Condition
    1 - 2
    		Switch pin not pushed
    		Below 1 Ω
    Switch pin pushed
    		10 kΩ or higher
    3 - 4
    		Switch pin not pushed
    		10 kΩ or higher
    Switch pin pushed
    		Below 1 Ω

  1. Reinstall the stop light switch.



NGnext
REPLACE STOP LIGHT SWITCH
OK
next down

3.CHECK ECM (STP AND ST1 - VOLTAGE)
  1. Disconnect the A24 ECM connector. Camry

  2. Disconnect the A24 ECM connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage between terminals ST1- and STP of the A24 ECM connector and body ground.

    Standard voltage:
    Tester Connection
    		Brake Pedal Operation
    		Specified Condition
    ST1- (A24-35) - Body ground
    		Released
    		9 to 14 V
    Depressed
    		Below 1.5 V
    STP (A24-36) - Body ground
    		Released
    		Below 1.5 V
    Depressed
    		9 to 14 V

  1. Reconnect the ECM connector.



NGnext
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
next down
REPLACE ECM

4.INSPECT FUSE (STOP AND IGN FUSES)
  1. Remove the STOP and IGN fuses from the instrument panel J/B. Camry

  2. Remove the STOP and IGN fuses from the instrument panel J/B.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the STOP and IGN fuses.



NGnext
REPLACE FUSE (STOP AND/OR IGN FUSES)
OK
next down
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH)