Sfi System - P2119(2010/08 - )

Brand:

Toyota

Model Name:

Camry ACV40 GSV40

Manual:

Repair Manual

Section:

2Az-Fe Engine Control System

Title:

Sfi System

  1. Description

  2. Fail-safe

  3. Wiring diagram

  4. Inspection procedure

  5. Check any other dtcs output (in addition to dtc p2119)

  6. Read value using intelligent tester (throttle position)

  7. Inspect throttle with motor body assembly (resistance of throttle actuator)

  8. Inspect throttle with motor body assembly (visually check throttle valve)

  9. Read value using intelligent tester (throttle position)

  10. Replace throttle with motor body assembly

  11. Check whether dtc output recurs (dtc p2119)

DTC P2119 Throttle Actuator Control Throttle Body Range / Performance


​

DESCRIPTION

The electronic throttle control system is composed of the throttle actuator, throttle position sensor, accelerator pedal position sensor, and ECM. The ECM operates the throttle actuator to regulate the throttle valve in response to driver inputs. The throttle position sensor detects the opening angle of the throttle valve, and provides the ECM with feedback so that the throttle valve can be appropriately controlled by the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P2119
Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
  1. Electronic throttle control system
  2. ECM
  3. Wire harness or connector

FAIL-SAFE

When either of these DTCs, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

Refer to DTC P2102 (Click here).

INSPECTION PROCEDURE

HINT:
  1. Refer to "Data List / Active Test" [Throttle Position Command, Throttle Position No. 1, Throttle Motor Current, Throttle Motor Duty (Open), Throttle Motor Duty (Close)] (Click here).
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2119)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:

    Result
    		Proceed to
    DTC P2119 is output
    		A
    DTC P2119 and other DTCs are output
    		B
    HINT:
    If any DTCs other than P2119 are output, troubleshoot those DTCs first.


Bnext
GO TO DTC CHART (Click here)
A
next down

2.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position Command.

  1. Check the values displayed on the tester while fully depressing and releasing the accelerator pedal quickly.

    Result
    Result
    		Proceed to
    Throttle Position No. 1 does not change
    		A
    Throttle Position No. 1 changes even a little
    		B
    HINT:
    When a DTC is output, the system changes to fail-safe mode. Therefore, only use the data up until the time the DTC is stored for confirmation.


Bnext
Go to step 4
A
next down

3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)

  1. Inspect the throttle with motor body assembly (Click here).



NGnext
Go to step 6
OK
next down

4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

  1. Check for contamination between the throttle valve and housing. If necessary, clean the throttle body. Also, check that the throttle valve moves smoothly.

    OK:
    Throttle valve is not contaminated with foreign objects and moves smoothly.


NGnext
Go to step 6
OK
next down

5.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.

  1. Check the values displayed on the tester while wiggling the ECM wire harness.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Check for DTCs.

    Result
    Result
    		Proceed to
    Value in Data List changes when wire harness is wiggled, or DTC is output*
    		A
    Other than above
    		B
    *: As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).


Bnext
Go to step 7
A
next down
REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

  1. Replace the throttle with motor body assembly (Click here).


NEXT
next down

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Allow the engine to idle for 15 seconds or more.

  1. Fully depress and release the accelerator pedal several times quickly.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:

    Result
    		Proceed to
    No DTC output
    		A
    DTC P2119 is output
    		B


Bnext
REPLACE ECM (Click here)
A
next down
END